A neoprene lumbar support cushion is a shaped cushion of laminated neoprene (SBR, SCR or CR foam + fabric), usually 5 mm thick, that sits behind the lower back on an office chair or a car seat so the sitter can sit comfortably for a long time. Office brands, car accessory sellers and gift companies order it for office chairs and car seats. It is a cushion placed behind the back, not a belt worn on the body. Send us your design drawing and cushion size, and we will confirm the best material and thickness.
We manufacture custom neoprene lumbar support cushions in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished lumbar support cushions under one roof, so a change to the size or the print can be checked on a sample before bulk production starts.
A lumbar cushion is judged by its shape: if the curve is wrong, it pushes the back in the wrong place and the sitter takes it away, so we cut the cushion to a contoured shape that follows the lower back, thicker in the middle and thinner at the edges, and we check the finished cushion by placing it on a chair and pressing the curve, because a cushion that is flat is a cushion that does not support anything.
The cushion stays on the chair all day, so the fixing is where it is judged. We fit a strap to your drawing that holds the cushion to the chair back without slipping down, and we stitch the strap through the cushion body and bar-tack the fixing points, because a cushion that slides down to the seat by lunchtime is a cushion the office will throw in a cupboard.
The cushion sits against the back for hours, so the face has to be comfortable and easy to clean. We use a fabric face that feels soft against a shirt and takes a printed logo cleanly, and the foam inside holds its shape through a long working day instead of flattening by the afternoon, and the whole cushion wipes clean after a spill.
5 mm is the standard for most neoprene lumbar support cushions. It gives a good balance of support, comfort and a cushion that holds its contoured shape, which is why most of the lumbar cushions we make are cut in 5 mm. For the full range, see our neoprene sheet thickness guide.
| Thickness | Best for | Trade-off |
|---|---|---|
| 3 mm | Slim lumbar cushions for light support and travel; easy to carry | Least support; not enough for a long day in a chair |
| 5 mm | Most lumbar cushions for office chairs and car seats; daily use | Best balance of support, comfort and a held shape |
| 7 mm | Thick lumbar cushions for maximum support on long drives | Most support, but bulky behind the back |
Measure the chair, not the person. Take the width of the chair back where the cushion will sit and the height of the lower back area, because a cushion ordered by body size alone often ends up too wide for a narrow office chair or too short to reach the lower back. See our custom neoprene lumbar support cushions — contoured, for office chairs and car seats, 3–8 mm for the styles this thickness choice applies to. For a cushion you sit on rather than lean against, our neoprene seat cushions are the closer page.
SBR is the standard choice for most lumbar support cushions, and CR is the choice where the cushion will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a cushion used in an office or a car. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a cushion sold with outdoor gear or used in strong sun.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it follows the curve of the lower back without a fight; SBR is firmer and holds the contoured shape through a long working day. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor use and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Office and car lumbar cushions | Outdoor and premium lumbar cushions |
For support worn on the body rather than placed on a chair, our neoprene back braces are the closer page.
Office brands — your own logo on a lumbar cushion your customers use at their desks every day, made to your cushion size.
Car accessory sellers — a lumbar cushion for drivers on long journeys, with a strap that holds it to the seat, for customers who drive for hours.
Gift companies — a lumbar cushion as a corporate gift or a welcome pack item, in your colours, for office workers and drivers.
Retailers and home office shops — a lumbar cushion sold on its own or with a seat cushion, sized to your chair, for customers who sit for a long time.
When neoprene is NOT the right choice
Tell us which of these your lumbar support cushions need, and we will build the sample to your drawing.
Will the cushion stay in place, or slide down the chair?
It stays in place if the strap is right. We fit a strap that holds the cushion to the chair back, and we stitch it through the cushion body, so it does not slide down to the seat by lunchtime.
Is it for an office chair or a car seat?
Both. The same contoured cushion works on an office chair and on a car seat, so tell us the chair back width in your drawing and we cut it to fit.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and the chair back width and height and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the cushion size and chair type and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom neoprene lumbar support cushions to your cushion size, your chair type and your print, and we check the shape and the strap on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom neoprene lumbar support cushions and we will confirm the best material and thickness for your lumbar support cushions.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A lumbar cushion is judged by whether it stays behind the lower back all day. Send us the chair back size and we will make you a sample to try on a real chair.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.