We foam CR neoprene in our own factory in China, where we have made neoprene products for 15 years, and split it to 7 mm — the standard thickness for cold-water wetsuits, for wetsuit makers, dive brands and winter diving brands. Send us your design drawing or specification, thickness and sheet size, and we will confirm the best foam grade for your product.
| Material CR neoprene foam | Thickness 7 mm | Minimum order 20 sheets as a general minimum, adjustable | Lead time 15–18 days after order confirmation |
A 7 mm sheet is about warmth. Thick foam traps more air, and trapped air is what keeps a diver warm on a long dive in cold water. That is why cold-water wetsuits are cut from 7 mm foam, while warm-water suits use a thinner split from the same CR rubber.
We foam the CR rubber, split the bun to 7 mm, and check the thickness across the sheet before it leaves the line. The sheet can be supplied plain, or laminated with nylon, T-fabric, polyester or lycra, on one side or both, in your colours. Our neoprene CR foam sheets page shows the cold-water wetsuit uses in more detail.
Cold water is the home of this sheet. It suits winter wetsuits, cold-water diving suits and thick water sports products — the products people wear when the water is cold and the dive is long. A 7 mm sheet is heavier and stiffer than a thin split, so we recommend it only where the water really needs it, and we will tell you so before you order.
Warmth is only half the story. The measured figures matter too: this CR foam is hardness 3–5° Shore C, density 276.32 kg/m³, tensile strength 860 kPa and elongation 550% (TDS v21). Those are measured figures from our own foaming line, and the table below carries them in full. If you are unsure how thickness changes the feel of a sheet, our neoprene sheet thickness guide explains it step by step.
This product is split to 7 mm. The question is whether 7 mm is right for your product, or whether a thinner sheet would serve it better.
3 mm — warm-water wetsuits. Our most used split for warm water, light and flexible, for summer suits and short wetsuits — see our custom neoprene 3mm CR foam sheets.
5 mm — cooler water and general wetsuits. The middle of our range, for wetsuits that need real warmth as well as flexibility.
7 mm — cold-water wetsuits, the standard cold-water thickness. The warmest standard split for diving suits, for cold water and long dives, up to 45 mm on request from the same CR foam.
Tell us the product and the water it will be used in, and we will recommend the thickness — this 7 mm sheet, or a thinner split from the same CR foam.
| Item | Specification |
|---|---|
| Material | CR neoprene foam |
| Thickness | 7 mm |
| Sheet Size | 51″ × 130″ |
| Hardness | 3–5° Shore C |
| Density | 276.32 kg/m³ |
| Tensile Strength | 860 kPa |
| Elongation | 550% |
| Lamination | Nylon, T-fabric, polyester or lycra, single or double-sided |
| Application | Cold-water wetsuits, winter diving suits |
CR, SCR and SBR are the three foams we work with. CR (chloroprene rubber) is the firmest and most resilient of the three, and the usual choice for diving and water sports. SBR (styrene-butadiene rubber) is softer and lighter, and the usual choice for everyday consumer products such as bags, sleeves and pads. SCR is a blend of the two, sitting between them in feel and performance, and the usual choice for sports and protective products. Tell us the product and we will help you pick the foam.
| Wetsuit makers — 7 mm CR sheets for cold-water wetsuits, cut and laminated to your specification and your colours. | Dive brands — 7 mm foam for winter suits and the thickest products in a dive range, made to your tech pack. |
| Cold-water sports brands — 7 mm CR foam for winter water sports goods and thick products that need the most insulation. | Foam distributors — standard sheets in 51″ × 130″, supplied plain or laminated, for resale to makers in your market. |
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
Is 7mm the right thickness for a cold-water wetsuit?
Yes — 7 mm is the standard thickness for cold-water wetsuits. It gives the most warmth of our standard splits, for cold water and long dives.
Why is 7mm the standard thickness for cold-water wetsuits?
Because thick foam traps more air, and trapped air is what keeps a diver warm on a long dive in cold water. A thinner split cannot give the same warmth, so 7 mm is the thickness cold-water wetsuit makers ask for most.
Can 7mm CR sheets be laminated with fabric?
Yes. We laminate nylon, T-fabric, polyester or lycra onto the foam, on one side or both, in your colours.
What is the minimum order?
20 sheets as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling. Send us your specification and we will confirm the sample details.
How do I order?
Send your design drawing, the foam grade, thickness and sheet size. We confirm the details, then make a sample for your approval before bulk production.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.