We foam CR neoprene in our own factory in China, where we have made neoprene products for 15 years, and split it to 3 mm — the most used thickness for warm-water wetsuits, for wetsuit makers, dive brands and water sports brands. Send us your design drawing or specification, thickness and sheet size, and we will confirm the best foam grade for your product.
| Material CR neoprene foam | Thickness 3 mm | Minimum order 20 sheets as a general minimum, adjustable | Lead time 15–18 days after order confirmation |
A 3 mm sheet is the warm-water standard. It is thick enough to take the chill off warm water and to protect the wearer from board rash and scrapes, and thin enough to paddle, swim and move freely in. That balance is why most warm-water wetsuits are cut from 3 mm foam.
We foam the CR rubber, split the bun to 3 mm, and check the thickness across the sheet before it leaves the line. The sheet can be supplied plain, or laminated with nylon, T-fabric, polyester or lycra, on one side or both, in your colours. Our neoprene CR foam sheets page shows the wetsuit and water sports uses in more detail.
Warm water is the home of this sheet. It suits summer wetsuits, short wetsuits, rash guard linings and light water sports products — the products people wear when the water is warm and the session is long. If your wetsuits are for cold water, a thicker split from the same CR foam is the right choice, and we will tell you so before you order.
Thickness is only half the story. The measured figures matter too: this CR foam is hardness 3–5° Shore C, density 276.32 kg/m³, tensile strength 860 kPa and elongation 550% (TDS v21). Those figures are from our own foaming line, and they are the figures in the table below. The same CR foam also goes into our custom neoprene dive boots, cut to the thickness each product needs. If you are unsure how thickness changes the feel of a sheet, our neoprene sheet thickness guide explains it step by step.
This product is split to 3 mm. The question is whether 3 mm is right for your product, or whether a thinner or thicker sheet would serve it better.
1.5 mm — light linings and the thinnest wetsuits. Our thinnest CR split, for linings inside thicker products and for the lightest warm-water tops, where flexibility matters most.
3 mm — warm-water wetsuits, the most used thickness. The standard split for warm-water wetsuits and water sports products, with the best balance of warmth and freedom of movement.
5–7 mm — cooler water and thicker products. For wetsuits that need more warmth than a 3 mm sheet gives, up to 45 mm on request from the same CR foam.
Tell us the product and the water it will be used in, and we will recommend the thickness — this 3 mm sheet, or a thinner or thicker split from the same CR foam.
| Item | Specification |
|---|---|
| Material | CR neoprene foam |
| Thickness | 3 mm |
| Sheet Size | 51″ × 130″ |
| Hardness | 3–5° Shore C |
| Density | 276.32 kg/m³ |
| Tensile Strength | 860 kPa |
| Elongation | 550% |
| Lamination | Nylon, T-fabric, polyester or lycra, single or double-sided |
| Application | Warm-water wetsuits, water sports |
CR, SCR and SBR are the three foams we work with. CR (chloroprene rubber) is the firmest and most resilient of the three, and the usual choice for diving and water sports. SBR (styrene-butadiene rubber) is softer and lighter, and the usual choice for everyday consumer products such as bags, sleeves and pads. SCR is a blend of the two, sitting between them in feel and performance, and the usual choice for sports and protective products. Tell us the product and we will help you pick the foam.
| Wetsuit makers — 3 mm CR sheets for warm-water wetsuits, cut and laminated to your specification and your colours. | Dive brands — 3 mm foam for summer suits and short wetsuits, made to your tech pack and your size range. |
| Water sports brands — 3 mm CR foam for surf tops, swim products and light water sports goods that need flexibility first. | Foam distributors — standard sheets in 51″ × 130″, supplied plain or laminated, for resale to makers in your market. |
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
Is 3mm the right thickness for a warm-water wetsuit?
Yes — 3 mm is the most used thickness for warm-water wetsuits. It gives enough warmth for warm water while staying flexible enough to paddle and swim in.
What are the measured figures for this CR foam?
Hardness 3–5° Shore C, density 276.32 kg/m³, tensile strength 860 kPa and elongation 550% (TDS v21). The foam is RoHS and REACH compliant.
Can 3mm CR sheets be laminated with fabric?
Yes. We laminate nylon, T-fabric, polyester or lycra onto the foam, on one side or both, in your colours.
What is the minimum order?
20 sheets as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling. Send us your specification and we will confirm the sample details.
How do I order?
Send your design drawing, the foam grade, thickness and sheet size. We confirm the details, then make a sample for your approval before bulk production.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.