We foam CR neoprene in our own factory in China, where we have made neoprene products for 15 years, and punch it with small holes — perforated CR foam that lets air through, for sports supports, braces and breathable products that a solid sheet would make too hot to wear. Send us your design drawing or specification, hole pattern, thickness and sheet size, and we will confirm the best foam grade for your product.
| Material CR neoprene foam, perforated | Thickness 1.5–45 mm | Minimum order 20 sheets as a general minimum, adjustable | Lead time 15–18 days after order confirmation |
A perforated sheet is a CR sheet with air flow. The holes run through the foam, so sweat and heat escape instead of building up under the product. A brace, a support sleeve or a sports pad worn for hours needs that air flow — a solid sheet keeps the warmth in, and after an hour the wearer feels it.
We foam the CR rubber, split the bun to your thickness, and punch the holes in your pattern before the sheet leaves the line. The sheet can be supplied plain, or laminated with nylon, T-fabric, polyester or lycra, on one side or both, in your colours — the holes stay open through the lamination, so the air flow survives the finished product.
The holes change how the sheet behaves, and that is the point. A perforated sheet stretches a little more easily and feels lighter on the body than the same thickness in solid foam, so supports made from it move with the wearer instead of fighting them. It is the same foam we use for our custom neoprene calf sleeves and other sports supports. Our neoprene CR foam sheets page shows the support and brace uses in more detail.
Measured figures are the same CR foam as our solid sheets: hardness 3–5° Shore C, density 276.32 kg/m³, tensile strength 860 kPa and elongation 550% (TDS v21). Those figures are from our own foaming line, and they are the figures in the table below. If you are unsure how thickness changes the feel of a sheet, our neoprene sheet thickness guide explains it step by step.
The thickness here is the foam thickness under the holes. The hole pattern is the same; the foam is what changes the feel of the finished support.
Thin foam — light supports and linings. A thin perforated foam keeps the sheet light and easy to sew, for light braces and supports that should flex with the body.
Medium foam — the most popular choice. Our most ordered thickness for perforated CR sheets, with real support and air flow for sports braces and protective products.
Thick foam — firm supports and warm products. A thick perforated foam gives the most support and warmth, for braces and pads that hold their shape under load.
Tell us the product and how long it will be worn, and we will recommend the foam thickness — from 1.5 mm to 45 mm, to your specification.
| Item | Specification |
|---|---|
| Material | CR neoprene foam, perforated |
| Thickness | 1.5–45 mm |
| Sheet Size | 51″ × 130″ |
| Hardness | 3–5° Shore C |
| Density | 276.32 kg/m³ |
| Tensile Strength | 860 kPa |
| Elongation | 550% |
| Lamination | Nylon, T-fabric, polyester or lycra, single or double-sided |
| Application | Sports supports, braces, breathable products |
CR, SCR and SBR are the three foams we work with. CR (chloroprene rubber) is the firmest and most resilient of the three, and the usual choice for diving and water sports. SBR (styrene-butadiene rubber) is softer and lighter, and the usual choice for everyday consumer products such as bags, sleeves and pads. SCR is a blend of the two, sitting between them in feel and performance, and the usual choice for sports and protective products. Tell us the product and we will help you pick the foam.
| Sports support makers — perforated CR sheets for braces and supports, cut and laminated to your specification and your colours. | Brace and protective brands — breathable foam for elbow, knee and ankle supports that are worn for hours at a time. |
| Garment makers — perforated sheets for breathable panels inside wetsuits, boots and gloves, where air flow matters most. | Foam distributors — standard sheets in 51″ × 130″, supplied plain or laminated, for resale to makers in your market. |
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
Do the holes go all the way through the foam?
Yes. The holes are punched through the sheet, so air passes through the foam and the lamination. That is what makes the sheet breathable.
Is perforated CR weaker than solid CR?
The foam is the same CR foam — hardness 3–5°, tensile 860 kPa, elongation 550% (TDS v21). The holes make the sheet more flexible, so we recommend checking the thickness with a sample for load-bearing supports.
Can perforated sheets be laminated with fabric?
Yes. We laminate nylon, T-fabric, polyester or lycra onto the foam, on one side or both, and the holes stay open through the lamination.
What is the minimum order?
20 sheets as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling. Send us your specification and hole pattern and we will confirm the sample details.
How do I order?
Send your design drawing, the foam grade, hole pattern, thickness and sheet size. We confirm the details, then make a sample for your approval before bulk production.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.