NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene SBR Foam Sheets
  • Neoprene SBR Foam Sheets
  • Neoprene SBR Foam Sheets
Neoprene SBR Foam SheetsNeoprene SBR Foam SheetsNeoprene SBR Foam Sheets

Neoprene SBR Foam Sheets

A neoprene SBR foam sheet is a flat sheet of SBR foam, usually 3 mm thick, that bag makers, sleeve makers and consumer-goods factories cut, laminate and stitch into finished products. SBR (styrene-butadiene rubber) is the lower-cost foam in our range, and it is the usual choice where the finished product is used indoors or wiped clean after use. It is not a CR sheet, so it does not match CR for sun, ozone or seawater use. Send us your design drawing, the sheet size and the thickness, and we will confirm the best SBR sheet for bags, sleeves and consumer goods.

We manufacture custom neoprene SBR foam sheets in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished SBR foam sheet under one roof, so a change to the thickness or the sheet size can be checked on a sample before bulk production starts.

A foam sheet is judged by how it cuts, so the cell structure matters more than the colour. We foam the SBR sheet in our own factory in China, where we have made neoprene products for 15 years, and we check the sheet for even thickness across the full width before it is packed, because a sheet that is thick on one side and thin on the other wastes material at the cutting table. The sheet is supplied plain or laminated with fabric to your order, and it can be cut to your sheet size so it fits your cutting table without trimming.

 

What thickness of neoprene SBR foam sheet should I order?

3 mm is the standard for most SBR foam sheets. It gives a good balance of cutting ease, cushioning and a sheet that still laminates flat, which is why most of the SBR foam sheets we make are cut in 3 mm. For the full range, see our neoprene sheet thickness guide.

1.5 mmThin sheets for linings, light sleeves and products that must fold flatLeast cushioning; not enough for a padded product
3 mmMost SBR sheets; bags, sleeves and consumer goodsBest balance of cutting ease, cushioning and a flat laminate
5 mmPadded bags, thick sleeves and products that need more bodyMost cushioning, but heavier and harder to fold

Measure the finished product, not the sheet. Tell us what you will make from the sheet, the finished thickness you need and the sheet size your cutting table takes: a sheet ordered by thickness alone often comes in the wrong size for the table, or too thin for the finished product. If you laminate the sheet yourself, tell us the fabric you use, so we match the foam face to your glue and your press. See our custom SBR foam sheets — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a foam sheet with more stretch than SBR rather than the lower-cost SBR sheet itself, our neoprene SCR foam sheets are the closer page.

 

SBR or CR neoprene — which is right for SBR foam sheets?

SBR is the standard choice for most foam sheets, and CR is the choice where the finished product will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for bags, sleeves and consumer goods used indoors or wiped clean after use. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a sheet that will become a wetsuit, a dive product or beach gear.

The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it stretches further when it is laminated and shaped; SBR is firmer and holds a flat sheet shape on the cutting table. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forBags, sleeves and consumer goods made indoorsWetsuits, dive gear and beach products

If the sheet needs more stretch than SBR without the cost of CR, the grade changes: Our neoprene CR foam sheets are cut from the same laminated neoprene, and the two are ordered from different patterns.

 

Who are neoprene SBR foam sheets for — and who are they not for?

Bag makers — sheets in your thickness and size for cutting into bags, sleeves and cases, made to your cutting table.

Sleeve makers — even-thickness sheets that laminate flat, for laptop sleeves, bottle sleeves and protective covers.

Consumer-goods factories — SBR sheets for coasters, mats, pads and promotional goods, cut to your size.

Shoe and glove makers — sheets for insoles, linings and soft parts, in the thickness your pattern needs.

When neoprene is NOT the right choice

  • If the finished product will live in sun or seawater — CR foam holds up longer than SBR in sun, ozone and salt air.
  • If the sheet must stretch a long way — SBR stretches less than CR, so a high-stretch product needs a different foam.
  • If the sheet is for a wetsuit — wetsuit foam is CR, not SBR, and the two should not be swapped.
  • If the lowest possible unit cost is the whole brief — tell us the target first, because a thinner SBR sheet may fit the budget better than a thick one.

 

Customisation Options

Tell us which of these your SBR foam sheet needs, and we will build the sample to your drawing.

  • Logo: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: made to your thickness, from thin linings to padded sheets, in the size your table takes.
  • Lamination: plain foam or laminated with nylon jersey or another fabric face to your order.
  • Fabric face: smooth nylon jersey or another fabric face to your design.
  • Packaging: polybag as standard; hangtag and retail packaging on request.

 

Frequently Asked Questions

Can I order SBR sheets cut to my table size?
Yes. Tell us the sheet length and width your cutting table takes and we cut the sheets to that size before packing, so you do not trim offcuts on arrival — send the size with your drawing.

How do I choose between SBR and SCR sheets?
Choose SBR for the lowest cost where the product is used indoors or wiped clean, and SCR where you want more stretch than SBR without paying for CR. Tell us the finished product and we will confirm the grade and thickness for it.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the sheet size, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We cut custom neoprene SBR foam sheets to your size and thickness, and we check the thickness across the full sheet before packing. The general minimum order is 20 sheets per order, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom SBR foam sheets and we will confirm the best material and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The sheet size your cutting table takes
  3. The thickness you need
  4. Thickness or material preference — SBR, SCR or CR
  5. Logo and colours
  6. Packaging — polybag, hangtag or retail packaging

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A foam sheet is judged at the cutting table, not in the warehouse. Send us the finished product and we will suggest the right SBR thickness.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.