NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Bags

  • Neoprene Can Coolers
  • Neoprene Can Coolers
  • Neoprene Can Coolers
Neoprene Can CoolersNeoprene Can CoolersNeoprene Can Coolers

Neoprene Can Coolers

A neoprene can cooler is a snug sleeve made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 3 mm thick, that wraps one can to keep it cold and to stop condensation wetting the hand. Drinks brands, bars and gift shops order it for cans, cold drinks and parties, because it grips the can, folds flat to post and prints well. It holds one standard can only. Send us your design drawing, the can size and the cooler style, and we will confirm the best material and thickness for cans, cold drinks and parties.

We manufacture custom neoprene can coolers in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished can cooler under one roof, so a change to the can size or the print can be checked on a sample before bulk production starts.

A can cooler is judged by the grip, so the fit matters more than the print. We cut the cooler to the can size so it grips without sliding off, and the base is stitched flat so the cooler stands on a table instead of tipping over. The print is put on before the cooler is cut where the design allows it, because a print laid down first sits square on the finished cooler instead of drifting to one side, and the whole cooler wipes clean after a party.

 

What thickness of neoprene is best for a can cooler?

3 mm is the standard for most can coolers. It gives a good balance of insulation, a snug fit and a cooler that still folds flat, which is why most of the can coolers we make are cut in 3 mm. For the full range, see our neoprene sheet thickness guide.

3 mmMost can coolers; parties, bars and everyday useBest balance of insulation and a slim, foldable fit
5 mmCoolers for long outdoor events and for a padded feelMore insulation, but thicker and less pocket-friendly
7 mmPremium coolers and coolers for very hot daysMost insulation, but bulky for a pocket

Measure the can, not the cooler you already own. Tell us the can height and diameter — standard, slim or tall — and send the artwork at the same size as the finished cooler: a cooler ordered by can name alone often fits the height and gaps at the sides, or fits the sides and pulls short at the top. See our custom can coolers — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a cooler with a full-colour print rather than a plain can cooler, our neoprene printed can coolers are the closer page.

 

SBR or CR neoprene — which is right for can coolers?

SBR is the standard choice for most can coolers, and CR is the choice where the cooler will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a cooler used at a party, a barbecue or a bar. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a cooler sold with beach gear or left in the sun.

The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the can without a fight; SBR is firmer and holds the cooler flat and neat when it is folded. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday can coolers for parties and barsBeach, outdoor and premium can coolers

If the drink needs a carrier for six cans rather than a sleeve for one, the shape changes: Our neoprene 6-pack bottle carriers are cut from the same laminated neoprene, and the two are ordered from different patterns.

 

Who is a neoprene can cooler for — and who is it not for?

Drinks brands — a cooler printed with your logo that travels with the cans you sell, made to fit your can size exactly.

Bars and breweries — coolers for your taproom and your merch shelf, so every can carries your name to the table.

Gift shops — coolers for party sets and summer gifts, in colours that match the season.

Event organisers — a branded cooler for festivals and corporate events, in your colours, that guests keep after the event.

When neoprene is NOT the right choice

  • If the cooler must hold a bottle — a bottle cooler is cut to a bottle shape, not a can shape, and the two should not be swapped.
  • If the can must stay cold for hours — a cooler bag with an insulated lining keeps a drink cold longer than a single-can sleeve.
  • If the cooler must hold a slim can — a slim can needs its own pattern, not a standard can cooler.
  • If the lowest possible unit cost is the whole brief — a thin paper sleeve fits a one-season budget better than a neoprene cooler.

 

Customisation Options

Tell us which of these your can cooler needs, and we will build the sample to your drawing.

  • Logo: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Print: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Can size: made to your can height and diameter — standard, slim or tall.
  • Fabric face: smooth nylon jersey or another fabric face to your design.
  • Packaging: polybag as standard; hangtag and retail packaging on request.

 

Frequently Asked Questions

Will the cooler fit a slim can as well as a standard can?
No, not from the same pattern. A slim can is narrower than a standard can, so it needs its own cut — tell us which can sizes you need and we will make a pattern for each, so every cooler grips its can.

Does the cooler stop condensation wetting my hand?
Yes, that is the point of the foam. The neoprene wraps the cold can and takes the condensation, so the hand stays dry — and the cooler wipes clean after use.

What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the can size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We make custom can coolers to your drawing, your size and your print, and we check the grip and the print on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom can coolers and we will confirm the best material and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The can height and diameter — standard, slim or tall
  3. The quantity you need
  4. Thickness or material preference — SBR, SCR or CR
  5. Logo and colours
  6. Packaging — polybag, hangtag or retail packaging

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A can cooler is judged by a cold can in a dry hand. Send us the can size and we will make you a sample to try with a real can.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.