NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Bags

  • Neoprene Printed Can Coolers
  • Neoprene Printed Can Coolers
  • Neoprene Printed Can Coolers
Neoprene Printed Can CoolersNeoprene Printed Can CoolersNeoprene Printed Can Coolers

Neoprene Printed Can Coolers

A neoprene printed can cooler is a snug sleeve made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 3 mm thick, that wraps one can to keep it cold and to carry a full-colour print for a brand, an event or a promotion. Drinks brands, event organisers and gift shops order it for printed cans, promos and events, because the whole surface prints and the cooler folds flat to post. It holds one standard can only. Send us your design drawing, the can size and the artwork, and we will confirm the best material and thickness for printed cans, promos and events.

We manufacture custom neoprene printed can coolers in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished printed can cooler under one roof, so a change to the can size or the print can be checked on a sample before bulk production starts.

A printed can cooler is judged by the print, so the artwork matters more than the stitching. We print the fabric face before the cooler is cut where the design allows it, because a print laid down first sits square on the finished cooler instead of drifting to one side, and the cooler is cut to the can size so it grips the can without sliding off. The base is stitched flat so the cooler stands on a table, and the whole cooler wipes clean after a party.

 

What thickness of neoprene is best for a printed can cooler?

3 mm is the standard for most printed can coolers. It gives a good balance of insulation, a snug fit and a cooler that still folds flat, which is why most of the printed can coolers we make are cut in 3 mm. For the full range, see our neoprene sheet thickness guide.

3 mmMost printed can coolers; parties, promos and eventsBest balance of insulation and a slim, foldable fit
5 mmCoolers for long outdoor events and for a padded feelMore insulation, but thicker and less pocket-friendly
7 mmPremium coolers and coolers for very hot daysMost insulation, but bulky for a pocket

Measure the can, not the cooler you already own. Tell us the can height and diameter — standard, slim or tall — and send the artwork at the same size as the finished cooler: a cooler ordered by can name alone often fits the height and gaps at the sides, or fits the sides and pulls short at the top. A slim can and a standard can need different patterns, so the can size must be planned first. See our custom printed can coolers — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a cooler cut for a slim can rather than a standard printed can, our neoprene slim can coolers are the closer page.

 

SBR or CR neoprene — which is right for printed can coolers?

SBR is the standard choice for most printed can coolers, and CR is the choice where the cooler will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a cooler used at a party, a barbecue or an event. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a cooler sold with beach gear or left in the sun.

The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the can without a fight; SBR is firmer and holds the cooler flat and neat when it is folded. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday printed can coolers for parties and promosBeach, outdoor and premium printed can coolers

If the drink needs a carrier for six cans rather than a sleeve for one, the shape changes: Our neoprene can coolers are cut from the same laminated neoprene, and the two are ordered from different patterns.

 

Who is a neoprene printed can cooler for — and who is it not for?

Drinks brands — a cooler printed with your full-colour artwork that travels with the cans you sell, made to fit your can size exactly.

Event organisers — a branded cooler for festivals, races and corporate events, in your colours, that guests keep after the event.

Gift companies — a printed cooler as a promotional item or a party favour, made to your artwork and your event date.

Bars and breweries — coolers for your taproom and your merch shelf, so every can carries your name to the table.

When neoprene is NOT the right choice

  • If the cooler must hold a bottle — a bottle cooler is cut to a bottle shape, not a can shape, and the two should not be swapped.
  • If the can must stay cold for hours — a cooler bag with an insulated lining keeps a drink cold longer than a single-can sleeve.
  • If the print must cover a very large area — a cooler prints one can, so a large banner needs a different product.
  • If the lowest possible unit cost is the whole brief — a thin paper sleeve fits a one-season budget better than a neoprene cooler.

 

Customisation Options

Tell us which of these your printed can cooler needs, and we will build the sample to your drawing.

  • Logo: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Print: sublimation for full-colour artwork across the whole cooler, or screen print for spot logos.
  • Can size: made to your can height and diameter — standard, slim or tall.
  • Fabric face: smooth nylon jersey or another fabric face to your design.
  • Packaging: polybag as standard; hangtag and retail packaging on request.

 

Frequently Asked Questions

Will my full-colour artwork print edge to edge?
Yes, if you send it at the right size. We print the fabric before cutting, so the artwork can run to the edges of the finished cooler — send the artwork at the finished cooler size and we will check it before we print.

Can I order different artwork on each cooler?
Yes, where you ask for it. Sublimation printing suits short runs of different designs, so tell us how many designs you need and we will confirm the best way to run them — one design per cooler costs more to set up than one design for the whole order.

What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the can size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We make custom printed can coolers to your drawing, your size and your print, and we check the print and the fit on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom printed can coolers and we will confirm the best material and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The can height and diameter — standard, slim or tall
  3. The quantity you need
  4. Thickness or material preference — SBR, SCR or CR
  5. Logo and colours
  6. Packaging — polybag, hangtag or retail packaging

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A printed can cooler is judged by the artwork on the table. Send us the can size and the artwork and we will make you a sample to try with a real can.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.