A neoprene fishing glove is a close-fitting glove made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 3 mm thick, that keeps the hands warm and grippy while fishing in cold water. Fishing shops, tackle brands and outdoor stores order it for fishing, grip and cold water, because it holds a rod, a reel and a wet line without slipping. It is not a dive glove, so it is not cut for the same grip and the same water use as a dive glove. Send us your design drawing, the hand sizes and the glove style, and we will confirm the best material and thickness for fishing, grip and cold water.
We manufacture custom neoprene fishing gloves in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished fishing glove under one roof, so a change to the fit or the cuff can be checked on a sample before bulk production starts.
A fishing glove is judged by the fingers, so the fingertips matter more than the palm. We cut the glove to the hand size with shaped fingers that follow the hand, so the angler can tie a knot and work a reel without taking the glove off, and the palm is finished with a grip face where you ask for it, so a wet rod does not twist in the hand. The cuff is cut to sit close at the wrist so water does not run down the sleeve, and the seams are placed where they do not rub between the fingers.
3 mm is the standard for most fishing gloves. It gives a good balance of grip, warmth and a glove that still lets the fingers work, which is why most of the fishing gloves we make are cut in 3 mm. For the full range, see our neoprene sheet thickness guide.
| 3 mm | Most fishing gloves; casting, reeling and knot tying | Best balance of grip, warmth and finger movement |
|---|---|---|
| 5 mm | Cold-water fishing and winter bank fishing | More warmth, but thicker fingers for fine work |
| 7 mm | Very cold water and long sessions in winter | Warmest, but stiff for tying small knots |
Measure the hand, not the glove size. Measure around the palm at the knuckles and the length from the wrist to the tip of the middle finger, and send both with your enquiry: a glove ordered by a letter size alone often fits the palm and pulls short at the fingers, or fits the fingers and gaps at the wrist. Tell us whether the fingertips should be full, half or open, because each cut needs a different pattern. See our custom fishing gloves — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a glove cut for diving rather than for casting and reeling, our neoprene diving gloves are the closer page.
SBR is the standard choice for most fishing gloves, and CR is the choice where the glove will be used in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a glove used on a river bank or a lake. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a glove sold for sea fishing or used in salt water every day.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it stretches further around bent fingers without a fight; SBR is firmer and holds the glove snug and square on the hand. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday fishing gloves for rivers and lakes | Sea fishing, salt water and premium fishing gloves |
If the angler needs a rod cover rather than a glove, the product changes: Our neoprene fishing rod covers are cut from the same laminated neoprene, and the two are ordered from different patterns.
Fishing shops — gloves in your sizes and colours for anglers who fish cold water, made to your size chart.
Tackle brands — a glove printed with your logo that anglers trust on the bank, made to your design and your grip.
Outdoor stores — gloves for river and sea fishing, where a warm hand and a sure grip matter more than a thin glove.
Fishing clubs — gloves in club colours for members, so the club name is seen on every bank and boat.
When neoprene is NOT the right choice
Tell us which of these your fishing glove needs, and we will build the sample to your drawing.
Can I tie knots without taking the gloves off?
Yes, if the fingertips are cut right. A 3 mm glove with shaped fingers lets most anglers tie a knot and work a reel, and a half-finger or open-fingertip cut gives even more feel — tell us the knot work and we will cut the fingertips to suit it.
Will the gloves work in salt water?
Yes, if you choose CR. CR foam resists seawater better than SBR, so a sea-fishing glove should be CR — tell us the water and we will confirm the foam before we cut.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the hand sizes and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom fishing gloves to your drawing, your size and your print, and we check the fit on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom fishing gloves and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A fishing glove is judged by a knot tied in cold water. Send us the hand sizes and we will make you a sample to try on a real rod.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.