NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Titanium Coated Foam Sheets
  • Neoprene Titanium Coated Foam Sheets
  • Neoprene Titanium Coated Foam Sheets
Neoprene Titanium Coated Foam SheetsNeoprene Titanium Coated Foam SheetsNeoprene Titanium Coated Foam Sheets

Neoprene Titanium Coated Foam Sheets

Neoprene titanium coated foam sheets are laminated neoprene sheets (SBR, SCR or CR foam + a titanium coated face), usually 3 mm thick, with a thin titanium layer that reflects body heat back to the wearer, for warm wetsuits that must insulate in cold water. Wetsuit makers, dive brands and cold-water swim brands order them for the inner or outer face of suits where warmth is the point. They are not plain foam sheets, so the titanium coat is part of the sheet and cannot be added later. Send us your design drawing, the products the sheets are cut for and the thickness, and we will confirm the best foam grade and thickness for warm wetsuits.

We make titanium coated foam sheets in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and finish the surface under one roof, so a change to the thickness or the finish can be checked on a sample before bulk production starts.

A titanium coat has to reflect heat, so the coat matters more than the thickness. We coat the titanium layer on the foam before lamination, so the coat stays even across the sheet, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The titanium face feels smooth on the skin, so a wetsuit slides on without the cold shock of a plain face.

The sheets are commonly supplied flat, because a flat sheet cuts cleanly on a maker's table and keeps the coat unmarked across panels. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished sheets by cutting a wetsuit panel from them and diving in it, because a coat that does not warm is a coat that ends up in the offcut bin.

 

What thickness of neoprene is best for titanium coated foam sheets?

3 mm is the standard for most titanium coated foam sheets. It gives a good balance of warmth, a smooth hand and a sheet that still cuts cleanly. For the full range, see our neoprene sheet thickness guide.

2 mmLight warm wetsuits for cool water where weight mattersLeast warmth; not enough for a cold-water dive
3 mmMost titanium coated foam sheets; warm wetsuitsBest balance of warmth, a smooth hand and an easy sew
5 mmCold-water wetsuits and diving suits that must insulateWarmest, but heavier and slower to dry

Measure the product, not the sheet name. Measure the largest panel the sheet must cover and the warmth the finished product needs, and tell us whether the product is sewn or glued: sheets ordered by name alone often fit the panel and leave no room for the seam, or cover the seam and pull short at the edge. See our custom titanium coated foam sheets — made to your thickness and size for the styles this thickness choice applies to. For a neoprene smooth skin foam sheets face rather than a titanium coated foam sheets face, see our neoprene smooth skin foam sheets.

 

SBR or CR neoprene — which is right for titanium coated foam sheets?

SBR is the standard foam for titanium coated sheets, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a warm wetsuit used in a pool or in cool water. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a warm wetsuit sold for the sea, cold water and daily diving.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the diver without a fight; SBR is firmer and holds a suit's shape when it is hung up to dry.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday warm wetsuitsCold-water, sea and premium warm wetsuits

If the sheet must be fast rather than warm, the product changes: our neoprene smooth skin foam sheets cut through water with less drag for triathlon, and a titanium coated sheet and a smooth skin sheet are ordered from different sheets.

 

Who is neoprene titanium coated foam sheets for — and who is it not for?

Wetsuit makers — titanium coated sheets in your colours, cut to your panel sizes, for warm wetsuits that hold body heat.

Dive brands — fabric in your colours for the suits you sell, made to fit your range exactly, so every diver stays warm.

Cold-water swim brands — a warm face for winter swimming suits, made to your thickness, for products where warmth is the point.

Print shops — titanium coated sheets that take print well, so your artwork stays bright after months in the water.

When neoprene is NOT the right choice

  • If the finished product is for warm water — a nylon or lycra face suits a warm-water brief better than a titanium coat.
  • If the coat must survive rough handling — a titanium coat marks easily, and a fabric face suits a hard-wearing brief better.
  • If the sheet is only for a lining — a thinner, lighter sheet fits a lining brief better than a 3 mm titanium coated sheet.
  • If the lowest possible unit cost is the whole brief — a plain foam sheet fits a one-season budget better than a titanium coated sheet.

 

Customisation Options

Tell us which of these your titanium coated foam sheets needs.

  • Print: screen print for spot logos on the titanium face, where the coat allows it.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: 2 mm, 3 mm or 5 mm, split to your order.
  • Foam grade: SBR, SCR or CR foam, to your design.
  • Sheet size: cut to your panel size, or supplied as full sheets.
  • Packaging: flat sheets as standard; rolls on request.

 

Frequently Asked Questions

Does the titanium coat really keep the wearer warmer?
Yes. The thin titanium layer reflects body heat back to the wearer, so a wetsuit stays warmer in cold water — tell us the suit and we check the warmth on the sample.

Will the titanium coat flake off when the sheet is cut?
No, not if the coat is done right. We coat the titanium layer on the foam before lamination, so the coat does not flake off when the sheet is cut and sewn — tell us the product and we check the coat on the sample.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We supply titanium coated foam sheets to your thickness, your print and your size, and we check the the warmth on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom titanium coated foam sheets and we will confirm the best foam grade and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The finished products the sheets are cut for
  3. The thickness you need
  4. Foam grade — SBR, SCR or CR
  5. Print and colours
  6. Packaging — flat sheets or rolls

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A titanium coated sheet is judged in cold water, not on a roll. Send us the product size and we will make you a sample sheet to cut.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.