Neoprene ribbed fabric is laminated neoprene (SBR, SCR or CR foam + a ribbed knit face), usually 3 mm thick, with raised ribs across the surface that give stretch and texture, for ribbed knit tops and bags that must look knitted and still cushion what is inside. Fashion brands, bag makers and knitwear makers order it for the outer face of tops and bags where the ribbed look is the point. It is sold as ribbed sheets for fashion makers to cut, not as a finished top or bag. Send us your design drawing, the products the fabric is cut for and the thickness, and we will confirm the best foam grade and thickness for ribbed knit tops and bags.
We make ribbed fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the ribbed face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.
A ribbed face has to stretch with the ribs, so the knit matters more than the colour. We laminate the ribbed knit face to the foam under heat and pressure, so the face does not peel at the cut edge, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The ribs run in one direction, so a top stretches across the body and holds its length.
The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and keeps the ribs lined up across panels. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for outdoor use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a top panel from it and stitching it, because a ribbed face that loses its ribs at the seam is a face that ends up in the offcut bin.
3 mm is the standard for most ribbed fabric. It gives a good balance of texture, stretch and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.
| 2 mm | Light ribbed knit tops and bags where texture matters most | Least padding; not enough for a product that must also cushion |
|---|---|---|
| 3 mm | Most ribbed fabric; ribbed knit tops and bags | Best balance of texture, stretch and an easy sew |
| 5 mm | Heavy fashion goods, work bags and tops that take a beating | Most padding, but heavier and stiffer to cut and sew |
Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the rib direction the design needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and runs the ribs the wrong way, or fits the ribs and pulls short at the edge. See our custom ribbed fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene quilted fabric face rather than a ribbed fabric face, see our neoprene quilted fabric.
SBR is the standard foam under a ribbed face, and CR is the choice where the finished product will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a ribbed top or bag used indoors or on land. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a ribbed top or bag sold for outdoor wear and use in the sun.
Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the body without a fight; SBR is firmer and holds a top's shape when it is hung up to dry.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday ribbed knit tops and bags | Outdoor and premium ribbed tops and bags |
If the face needs quilting rather than ribs, the product changes: our neoprene quilted fabric carry a padded diamond pattern for bags and fashion goods, and a ribbed face and a quilted face are ordered from different sheets.
Fashion brands — ribbed-faced sheets in your colours, cut to your panel sizes, for tops that look knitted.
Bag makers — a ribbed face for casual bags, made to your thickness, for products where the ribbed look is the point.
Knitwear makers — ribbed-faced sheets for knit tops, made to fit your range exactly.
Gift companies — ribbed-faced sheets for branded fashion goods, so your client's name looks at home on any casual product.
When neoprene is NOT the right choice
Tell us which of these your ribbed fabric needs.
Which way do the ribs run?
In one direction across the sheet. The ribs run in one direction, so a top stretches across the body and holds its length — tell us the product and we cut the panels with the ribs running the way your design needs.
Will the ribs flatten at the seam?
Not if the panels are cut right. We cut the panels with the ribs lined up across the seam, so the ribbed look runs across the finished top — tell us the product and we check the ribs on the sample.
What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We supply ribbed fabric to your thickness, your print and your size, and we check the the ribs on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom ribbed fabric and we will confirm the best foam grade and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A ribbed face is judged on the body, not on a roll. Send us the product size and we will make you a sample sheet to cut.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.