NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Smooth Skin Foam Sheets
  • Neoprene Smooth Skin Foam Sheets
  • Neoprene Smooth Skin Foam Sheets
Neoprene Smooth Skin Foam SheetsNeoprene Smooth Skin Foam SheetsNeoprene Smooth Skin Foam Sheets

Neoprene Smooth Skin Foam Sheets

Neoprene smooth skin foam sheets are laminated neoprene sheets (SBR, SCR or CR foam + a smooth rubber skin face), usually 3 mm thick, with a slick, uncoated rubber surface that cuts through water with less drag, for swimwear and triathlon suits where speed matters. Swim brands, triathlon brands and wetsuit makers order them for the outer face of racing suits, because smooth skin slides through water faster than a fabric face. They are not plain foam sheets, so the smooth skin is part of the sheet and cannot be added later. Send us your design drawing, the products the sheets are cut for and the thickness, and we will confirm the best foam grade and thickness for swimwear and triathlon.

We make smooth skin foam sheets in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and finish the surface under one roof, so a change to the thickness or the finish can be checked on a sample before bulk production starts.

A smooth skin face has to stay slick, so the skin matters more than the thickness. We finish the rubber skin on the foam before cutting, so the surface stays smooth and even across the sheet, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The smooth skin feels slick on the water, so a triathlon suit moves faster than a fabric-faced suit.

The sheets are commonly supplied flat, because a flat sheet cuts cleanly on a maker's table and keeps the skin unmarked across panels. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished sheets by cutting a suit panel from them and swimming in it, because a skin that drags is a skin that ends up in the offcut bin.

 

What thickness of neoprene is best for smooth skin foam sheets?

3 mm is the standard for most smooth skin foam sheets. It gives a good balance of low drag, a smooth hand and a sheet that still cuts cleanly. For the full range, see our neoprene sheet thickness guide.

2 mmLight swimwear and triathlon suits where low drag matters mostLeast warmth; not enough for a cold-water swim
3 mmMost smooth skin foam sheets; swimwear and triathlonBest balance of low drag, a smooth hand and an easy sew
5 mmCold-water triathlon suits and swimwear that must also insulateMost warmth, but heavier and slower to dry

Measure the product, not the sheet name. Measure the largest panel the sheet must cover and the speed the finished product needs, and tell us whether the product is sewn or glued: sheets ordered by name alone often fit the panel and leave no room for the seam, or cover the seam and pull short at the edge. See our custom smooth skin foam sheets — made to your thickness and size for the styles this thickness choice applies to. For a neoprene titanium coated foam sheets face rather than a smooth skin foam sheets face, see our neoprene titanium coated foam sheets.

 

SBR or CR neoprene — which is right for smooth skin foam sheets?

SBR is the standard foam for smooth skin sheets, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a swimsuit or triathlon suit used in a pool or on land. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a triathlon suit or swimwear sold for the sea, open water and daily salt-water use.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the swimmer without a fight; SBR is firmer and holds a suit's shape when it is hung up to dry.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday swimwear and triathlon suitsOpen-water, sea and premium triathlon suits

If the sheet must keep the swimmer warm rather than fast, the product changes: our neoprene titanium coated foam sheets hold body heat for warm wetsuits, and a smooth skin sheet and a titanium coated sheet are ordered from different sheets.

 

Who is neoprene smooth skin foam sheets for — and who is it not for?

Swim brands — smooth skin sheets in your colours, cut to your panel sizes, for racing suits that cut through water.

Triathlon brands — fabric in your colours for the suits you sell, made to fit your range exactly, so every athlete swims faster.

Wetsuit makers — a slick face for triathlon suits, made to your thickness, for products where speed is the point.

Print shops — smooth skin sheets that take print well, so your artwork stays bright after months in the water.

When neoprene is NOT the right choice

  • If the finished product needs a tough outer face — a nylon face stands up to daily wear better than a smooth skin face.
  • If the skin must survive rough handling — smooth skin marks easily, and a fabric face suits a hard-wearing brief better.
  • If the sheet is only for a lining — a thinner, lighter sheet fits a lining brief better than a 3 mm smooth skin sheet.
  • If the lowest possible unit cost is the whole brief — a plain foam sheet fits a one-season budget better than a smooth skin sheet.

 

Customisation Options

Tell us which of these your smooth skin foam sheets needs.

  • Print: screen print for spot logos on the smooth skin face, where the skin allows it.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: 2 mm, 3 mm or 5 mm, split to your order.
  • Foam grade: SBR, SCR or CR foam, to your design.
  • Sheet size: cut to your panel size, or supplied as full sheets.
  • Packaging: flat sheets as standard; rolls on request.

 

Frequently Asked Questions

Will the smooth skin mark easily?
It can mark if it is rubbed hard, which is true of any smooth rubber face. The skin is made to hold its slick finish through normal racing use — tell us the product and we check the skin on the sample.

Does smooth skin really swim faster?
Yes. The slick rubber surface cuts through water with less drag than a fabric face, so a triathlon suit moves faster — tell us the suit and we check the skin on the sample.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We supply smooth skin foam sheets to your thickness, your print and your size, and we check the the skin on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom smooth skin foam sheets and we will confirm the best foam grade and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The finished products the sheets are cut for
  3. The thickness you need
  4. Foam grade — SBR, SCR or CR
  5. Print and colours
  6. Packaging — flat sheets or rolls

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A smooth skin sheet is judged in the water, not on a roll. Send us the product size and we will make you a sample sheet to cut.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.