A neoprene table runner is a long narrow cloth made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 3 mm thick, that lies down the middle of a dining table to protect it and to dress it for a meal. Home shops and event suppliers order it for dining tables, banquets and home decor where the table needs both protection and colour. It is not a placemat, so it runs the full length of the table instead of sitting under one plate. Send us your design drawing, the table length and the runner style, and we will confirm the best material and thickness for dining tables and home decor.
We manufacture custom table runners in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished table runner under one roof, so a change can be checked on a sample before bulk production starts.
A table runner has to lie flat, so the cut length matters more than the colour. We cut the runner to the table length you ask for with a bound edge where you ask for it, so it does not curl up at the ends after months of use, and the ends can be left straight or shaped to your drawing. The base is made to grip the table so the runner does not slide when plates are set down, and the top face is smooth, so a spill sits on the surface instead of soaking in.
The runner is commonly made in one piece of foam where the design allows it, because a runner made from one piece lies flatter than a runner pieced together from offcuts. The face can be printed with your pattern where you ask for it, so the runner matches the room, and the whole runner wipes clean after a meal and is left to dry. We check the finished runner by laying it on a table and setting plates on it, because a runner that slides is a runner that ends up in a drawer.
3 mm is the standard for most table runners. It gives a good balance of a flat lay, wipe-clean care and a runner that still drapes at the ends. For the full range, see our neoprene sheet thickness guide.
| 2 mm | Light runners for short tables and for everyday meals | Least body; not enough to lie flat on a long table |
|---|---|---|
| 3 mm | Most table runners; dining tables and home decor | Best balance of a flat lay, wipe-clean care and a soft drape |
| 5 mm | Long banquet tables and runners that must hold a heavy centrepiece | Most body, but heavier and harder to fold for storage |
Measure the table, not the room. Measure the table length and width, and tell us how much overhang you want at each end: a runner ordered by guess alone often fits the table and leaves no drape at the ends, or drapes well and crowds the plates. See our custom table runners — made to your design, 3–8 mm for the styles this thickness choice applies to. For a camping sleeping pad rather than a table runner, see our neoprene camping sleeping pads.
SBR is the standard choice for most table runners, and CR is the choice where the runner will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a runner used indoors, on a dining table or at home. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a runner sold for garden tables, patios and outdoor dining in the sun.
Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it drapes at the ends without a fight; SBR is firmer and holds the runner flat and square on the table.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday table runners for dining rooms and homes | Outdoor, patio and premium table runners |
If the table needs a small mat under each plate rather than a long runner, the product changes: our neoprene-placemats-supplier are cut for one place setting each, and a runner and a placemat are ordered from different patterns.
Home shops — runners in colours that match the room, made to your table length, for customers who want a dressed table without buying new linen.
Event suppliers — matching runners for banquet tables, with your colours, for weddings, parties and conferences.
Restaurants — runners in your colours for the tables in your dining room, so every table looks dressed and your name is seen at every meal.
Gift companies — a branded runner as a housewarming gift, in your colours, for welcome packs and home events.
When neoprene is NOT the right choice
Tell us which of these your table runner needs.
Will the runner slide when plates are set down?
Not if the base is made for it. The base is made to grip the table so the runner does not slide when plates are set down, and we check the finished runner by setting plates on it — tell us the table surface in your enquiry.
Can the runner be printed with our pattern?
Yes. The face can be printed with your pattern where you ask for it, by sublimation for full-colour artwork — send the artwork with your drawing and we confirm the print before sampling.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom table runners to your drawing, your size and your print, and we check the the lay on a sample on a sample before bulk production. The general minimum order is 200 pieces per design as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom table runners and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A table runner is judged at the first dinner, not on a hanger. Send us the table size and we will make you a sample to try on a real table.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.