A neoprene sunglasses case is a soft sleeve made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 3–5 mm thick, that holds one pair of glasses to protect the lenses against scratches and knocks. Eyewear brands and gift shops order it for glasses carried in a bag, a pocket or a car. It holds one pair only. Send us your design drawing and glasses size, and we will confirm the best material and thickness for daily carry.
We manufacture custom neoprene sunglasses cases in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished case under one roof, so a change to the fit or the closure can be checked on a sample before bulk production starts.
A glasses case has to grip without scratching, so the inside matters more than the outside. We cut the case to the glasses size with a soft fabric face inside, so the lenses slide in without catching, and the foam outside cushions the frames against knocks in a bag. The opening is commonly a zip, a slip-in top or a fold-over flap to your drawing, and the zip is placed so its teeth never touch the lenses when the case is opened and closed.
The case is cut with a flat or shaped base so it stands on a desk instead of rolling away, and the seams are placed at the sides where they do not press on the frames. A clip, a loop or a small pocket can be added where you ask for it, so the case hangs from a bag or a belt, and the whole case wipes clean after a day in a beach bag. We check the finished case by sliding the real glasses in and out several times, because a case that is hard to open is a case that stays at home.
3 mm is the standard for most sunglasses cases. It gives a good balance of scratch protection, cushioning and a slim case that still fits in a pocket, which is why most of the cases we make are cut in 3 mm. For the full range, see our neoprene sheet thickness guide.
| 3 mm | Most sunglasses cases; daily carry in a bag or pocket | Best balance of protection and a slim fit |
|---|---|---|
| 5 mm | Glasses carried in a busy bag or a toolbox; extra cushioning | More protection, but thicker and less pocket-friendly |
| 7 mm | Expensive glasses and rough travel use | Most cushioning, but bulky for everyday carry |
Measure the glasses, not the case you already own. Measure the full width of the folded glasses and the height from the top of the frame to the bottom, and tell us whether the frames are wide or curved. See our custom sunglasses cases — made to your glasses size, 3–8 mm, with zip or slip-in opening for the styles this thickness choice applies to. For earphones rather than glasses, our neoprene headphone cases are the closer page.
SBR is the standard choice for most sunglasses cases, and CR is the choice where the case will live outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a case carried in a bag, a pocket or a car. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a case sold with beach gear or left in the sun.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the frames without a fight; SBR is firmer and holds the case flat and neat in a pocket. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday sunglasses cases for bags and pockets | Beach, outdoor and premium glasses cases |
If the glasses need hard drop protection rather than a soft sleeve, the product changes: our neoprene drone cases show how we build thicker padded cases, and a hard glasses case is a different product from a soft neoprene sleeve.
Eyewear brands — a case printed with your logo that travels with the glasses you sell, made to fit your frames exactly.
Gift companies — a branded case as a corporate gift or a promotional item, in your colours, for conferences, events and welcome packs.
Optical shops — cases for the glasses you dispense, sized to the frames you stock, so every customer leaves with protection for their new glasses.
Travel and outdoor shops — cases for glasses carried on holiday and outdoors, where a hard case is heavy and a soft case slips into a pocket.
When neoprene is NOT the right choice
Tell us which of these your case needs, and we will build the sample to your drawing.
Will the zip scratch my lenses?
No, not if the zip is placed right. The zip is set so its teeth never touch the lenses when the case is opened and closed, and the inside face is soft — tell us the frame shape and we place the opening to suit it.
Can I add a clip to hang the case from a bag?
Yes. A clip, a loop or a small pocket can be added where you ask for it, stitched and reinforced at the fixing point so it takes the weight of the case and the glasses inside.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom sunglasses cases to your drawing, your size and your print, and we check the fit on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom sunglasses cases and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A glasses case is judged every time the glasses go in and out. Send us the glasses size and we will make you a sample to try with real glasses.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.