NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Spandex Fabric
  • Neoprene Spandex Fabric
  • Neoprene Spandex Fabric
Neoprene Spandex FabricNeoprene Spandex FabricNeoprene Spandex Fabric

Neoprene Spandex Fabric

Neoprene spandex fabric is laminated neoprene (SBR, SCR or CR foam + a spandex face), usually 3 mm thick, that stretches further than any other face and springs back, for swimwear, dancewear and stretch gear that must move with the body in every direction. Swimwear makers, dancewear makers and competition brands order it for the outer face of costumes and suits that bend, twist and dive. It is sold as sheets for dancewear and swimwear makers to cut, not as a finished costume. Send us your design drawing, the products the fabric is cut for and the thickness, and we will confirm the best foam grade and thickness for swimwear, dancewear and stretch gear.

We make spandex fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the spandex face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.

A spandex face has to stretch and recover, so the lamination matters more than the colour. We laminate the spandex face to the foam under heat and pressure, so the face does not peel when the costume is pulled on, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The spandex face feels smooth on the skin, so a costume slides on without catching.

The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and wastes less than a roll that curls at the edges. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a costume panel from it and stretching it in every direction, because a face that does not spring back is a face that ends up in the offcut bin.

 

What thickness of neoprene is best for spandex fabric?

3 mm is the standard for most spandex fabric. It gives a good balance of maximum stretch, recovery and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.

2 mmLight swimwear, dancewear and stretch gear where stretch matters mostLeast padding; not enough for a cold-water suit
3 mmMost spandex fabric; swimwear, dancewear and stretch gearBest balance of maximum stretch, recovery and an easy sew
5 mmCold-water suits and stretch gear that must also insulateMost padding, but heavier and slower to dry

Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the stretch the finished product needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and leaves no room for the seam, or covers the seam and pulls short at the edge. See our custom spandex fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene loop fabric face rather than a spandex fabric face, see our neoprene loop fabric.

 

SBR or CR neoprene — which is right for spandex fabric?

SBR is the standard foam under a spandex face, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a swimsuit, dance costume or stretch garment used in a pool or on stage. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a swimsuit or surf suit sold for the sea, the beach and daily salt-water use.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the dancer without a fight; SBR is firmer and holds a costume's shape when it is hung up to dry.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday swimwear, dancewear and stretch gearSea, beach and premium swimwear and dancewear

If the face needs the stretch of lycra rather than the maximum stretch of spandex, the product changes: our neoprene lycra fabric stretch well for swimwear and surf suits at a lower cost, and a spandex face and a lycra face are ordered from different sheets.

 

Who is neoprene spandex fabric for — and who is it not for?

Swimwear makers — spandex-faced sheets in your colours, cut to your panel sizes, for swimwear that stretches in every direction.

Dancewear makers — a face that moves with the dancer, made to your thickness, for costumes that bend and twist.

Competition brands — fabric printed with your logo for the suits you sell, made to fit your range exactly.

Print shops — spandex-faced sheets that take sublimation print well, so your artwork stays bright after months of use.

When neoprene is NOT the right choice

  • If the finished product needs a tough outer face — a nylon face stands up to daily wear better than a spandex face.
  • If the face must not stretch at all — a polyester face holds its shape better than a spandex face.
  • If the fabric is only for a lining — a thinner, lighter face fits a lining brief better than a 3 mm laminated sheet.
  • If the lowest possible unit cost is the whole brief — an unlaminated foam sheet fits a one-season budget better than a spandex-faced sheet.

 

Customisation Options

Tell us which of these your spandex fabric needs.

  • Print: sublimation for full-colour artwork, screen print for spot logos, on the spandex face.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: 2 mm, 3 mm or 5 mm, split to your order.
  • Foam grade: SBR, SCR or CR foam under the face, to your design.
  • Sheet size: cut to your panel size, or supplied as full sheets.
  • Packaging: flat sheets as standard; rolls on request.

 

Frequently Asked Questions

Will the spandex face lose its stretch after use?
Not if the lamination is right. We laminate the spandex face to the foam under heat and pressure, so the face springs back after stretching in every direction — tell us the product and we check the recovery on the sample.

Can the face be printed with our artwork?
Yes. The spandex face takes sublimation print well, so your artwork stays bright after months of use — send the artwork with your drawing and we confirm the print before sampling.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We supply spandex fabric to your thickness, your print and your size, and we check the the stretch on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom spandex fabric and we will confirm the best foam grade and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The finished products the fabric is cut for
  3. The thickness you need
  4. Foam grade — SBR, SCR or CR
  5. Print and colours
  6. Packaging — flat sheets or rolls

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A spandex face is judged on the body, not on a roll. Send us the product size and we will make you a sample sheet to cut.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.