Neoprene loop fabric is laminated neoprene (SBR, SCR or CR foam + a loop face), usually 3 mm thick, that a hook strip grips anywhere on the surface, for hook-and-loop straps, braces and fasteners that must close at any point. Brace makers, strap makers and sports brands order it for the outer face of supports and straps where the fastening must land anywhere, not in one fixed spot. Brace makers buy it as flat sheets and cut it to their pattern; it is not a finished brace. Send us your design drawing, the products the fabric is cut for and the thickness, and we will confirm the best foam grade and thickness for hook-and-loop straps, braces and fasteners.
We make loop fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the loop face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.
A loop face has to grip, so the loop density matters more than the colour. We laminate the loop face to the foam under heat and pressure, so the loops do not peel at the cut edge, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The loop face takes a hook strip anywhere on the surface, so a brace strap closes exactly where the wearer needs it.
The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and wastes less than a roll that curls at the edges. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a brace panel from it and fastening a hook strap to it many times, because a loop face that stops gripping is a face that ends up in the offcut bin.
3 mm is the standard for most loop fabric. It gives a good balance of hook grip, durability and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.
| 2 mm | Light straps, braces and fasteners where weight matters | Least grip area; not enough for a strap that must hold a heavy load |
|---|---|---|
| 3 mm | Most loop fabric; hook-and-loop straps, braces and fasteners | Best balance of hook grip, durability and an easy sew |
| 5 mm | Heavy braces, work straps and fasteners that must hold all day | Most grip, but heavier and stiffer to cut and sew |
Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the strap area the fastening needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and leaves no room for the strap, or covers the strap and pulls short at the edge. See our custom loop fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene cotton fabric face rather than a loop fabric face, see our neoprene cotton fabric.
SBR is the standard foam under a loop face, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a brace, strap or fastener used on land or indoors. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a brace or strap sold for the beach, the sea and outdoor use.
Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the body without a fight; SBR is firmer and holds a brace's shape when it is hung up to dry.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday hook-and-loop straps, braces and fasteners | Beach, sea and premium straps and braces |
If the face needs a smooth surface rather than a loop surface, the product changes: our neoprene nylon fabric sew cleanly for wetsuits and bags, and a loop face and a nylon face are ordered from different sheets.
Brace makers — loop-faced sheets in your colours, cut to your panel sizes, for braces whose straps close anywhere.
Strap makers — a loop face for straps and fasteners, made to your thickness, for products where the fastening must land anywhere.
Sports brands — fabric in your colours for the supports you sell, made to fit your range exactly.
Medical suppliers — loop-faced sheets for supports worn all day, so the strap closes exactly where the wearer needs it.
When neoprene is NOT the right choice
Tell us which of these your loop fabric needs.
Will the hook strip grip anywhere on the loop face?
Yes. The loop face takes a hook strip anywhere on the surface, so a brace strap closes exactly where the wearer needs it — tell us the strap size and we check the grip on the sample.
Will the loops wear out after many fastenings?
Not if the lamination is right. We laminate the loop face to the foam under heat and pressure, so the loops hold their grip after many fastenings — tell us the product and we check the grip on the sample.
What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We supply loop fabric to your thickness, your print and your size, and we check the the grip on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom loop fabric and we will confirm the best foam grade and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A loop face is judged on the strap, not on a roll. Send us the product size and we will make you a sample sheet to cut.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.