Neoprene lycra fabric is laminated neoprene (SBR, SCR or CR foam + a lycra face), usually 3 mm thick, that stretches further than a nylon face and springs back, for swimwear, surf suits and stretch gear that must move with the body. Swimwear makers, surf brands and dancewear makers order it for the outer face of suits that bend, twist and dive. It comes as sheets for swimwear makers to cut, not as a finished swimsuit. Send us your design drawing, the products the fabric is cut for and the thickness, and we will confirm the best foam grade and thickness for swimwear, surf suits and stretch gear.
We make lycra fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the lycra face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.
A lycra face has to stretch and recover, so the lamination matters more than the colour. We laminate the lycra face to the foam under heat and pressure, so the face does not peel when the suit is pulled on, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The lycra face feels smooth on the skin, so a surf suit slides on without catching.
The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and wastes less than a roll that curls at the edges. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a surf suit panel from it and stretching it, because a face that does not spring back is a face that ends up in the offcut bin.
3 mm is the standard for most lycra fabric. It gives a good balance of stretch, recovery and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.
| 2 mm | Light swimwear, surf suits and dancewear where stretch matters most | Least padding; not enough for a cold-water suit |
|---|---|---|
| 3 mm | Most lycra fabric; swimwear, surf suits and stretch gear | Best balance of stretch, recovery and an easy sew |
| 5 mm | Cold-water surf suits and stretch gear that must also insulate | Most padding, but heavier and slower to dry |
Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the stretch the finished product needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and leaves no room for the seam, or covers the seam and pulls short at the edge. See our custom lycra fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene printed fabric face rather than a lycra fabric face, see our neoprene printed fabric.
SBR is the standard foam under a lycra face, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a swimsuit, surf suit or dance costume used in a pool or on land. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a surf suit or swimwear sold for the sea, the beach and daily salt-water use.
Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the swimmer without a fight; SBR is firmer and holds a suit's shape when it is hung up to dry.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday swimwear, surf suits and stretch gear | Sea, beach and premium swimwear and surf suits |
If the face needs the stretch of spandex rather than lycra, the product changes: our neoprene spandex fabric stretch further still for dancewear and competition swimwear, and a lycra face and a spandex face are ordered from different sheets.
Swimwear makers — lycra-faced sheets in your colours, cut to your panel sizes, for swimwear that stretches and recovers.
Surf brands — fabric printed with your logo for the suits you sell, made to fit your range exactly.
Dancewear makers — a face that moves with the dancer, made to your thickness, for costumes that bend and twist.
Print shops — lycra-faced sheets that take sublimation print well, so your artwork stays bright after months of use.
When neoprene is NOT the right choice
Tell us which of these your lycra fabric needs.
Will the lycra face lose its stretch after use?
Not if the lamination is right. We laminate the lycra face to the foam under heat and pressure, so the face springs back after stretching — tell us the product and we check the recovery on the sample.
Can the face be printed with our artwork?
Yes. The lycra face takes sublimation print well, so your artwork stays bright after months in the sea — send the artwork with your drawing and we confirm the print before sampling.
What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We supply lycra fabric to your thickness, your print and your size, and we check the the stretch on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom lycra fabric and we will confirm the best foam grade and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A lycra face is judged on the body, not on a roll. Send us the product size and we will make you a sample sheet to cut.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.