NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Adhesive-Backed Foam Sheets
  • Neoprene Adhesive-Backed Foam Sheets
  • Neoprene Adhesive-Backed Foam Sheets
Neoprene Adhesive-Backed Foam SheetsNeoprene Adhesive-Backed Foam SheetsNeoprene Adhesive-Backed Foam Sheets

Neoprene Adhesive-Backed Foam Sheets

Neoprene adhesive-backed foam sheets are laminated neoprene sheets (SBR, SCR or CR foam + fabric) with a sticky back, usually 3 mm thick, that press onto a surface and stay there, for stick-on padding that must not move. Equipment makers, case makers and sports brands order them for padding glued inside cases, onto handles and onto work surfaces where screws and stitching will not do. They are not plain foam sheets, so the adhesive is part of the sheet and cannot be added later. Send us your design drawing, the surfaces the sheets stick to and the thickness, and we will confirm the best foam grade and thickness for stick-on padding.

We make adhesive-backed foam sheets in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and finish the surface under one roof, so a change to the thickness or the finish can be checked on a sample before bulk production starts.

An adhesive-backed sheet has to stick, so the adhesive matters more than the thickness. We coat the adhesive on the back after lamination, so it bonds evenly across the sheet, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The adhesive holds on metal, plastic and wood, and the release paper peels off cleanly when the pad is placed.

The sheets are commonly supplied flat with release paper, because a flat sheet cuts cleanly on a maker's table and the release paper keeps the adhesive clean until use. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for outdoor use, and the whole sheet wipes clean after cutting. We check the finished sheets by sticking a pad to a real surface and pulling it, because a pad that peels off is a pad that ends up in the bin.

 

What thickness of neoprene is best for adhesive-backed foam sheets?

3 mm is the standard for most adhesive-backed foam sheets. It gives a good balance of stick, cushioning and a sheet that still cuts cleanly. For the full range, see our neoprene sheet thickness guide.

2 mmLight stick-on padding for small parts and liningsLeast cushioning; not enough for a pad that must also protect
3 mmMost adhesive-backed foam sheets; stick-on paddingBest balance of stick, cushioning and a clean cut
5 mmHeavy pads, work surfaces and padding that must stay putMost padding, but heavier and harder to peel and reposition

Measure the surface, not the sheet name. Measure the area the pad must cover and the weight it must hold, and tell us the surface material — metal, plastic or wood: sheets ordered by name alone often fit the area and peel off the surface, or stick well and pull short at the edge. See our custom adhesive-backed foam sheets — made to your thickness and size for the styles this thickness choice applies to. For a neoprene smooth skin foam sheets face rather than a adhesive-backed foam sheets face, see our neoprene smooth skin foam sheets.

 

SBR or CR neoprene — which is right for adhesive-backed foam sheets?

SBR is the standard foam for adhesive-backed sheets, and CR is the choice where the finished product will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for stick-on padding used indoors, in a case or on a work surface. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for stick-on padding sold for outdoor gear, boats and use in the sun.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it follows a curved surface without a fight; SBR is firmer and holds a pad flat and square on the surface.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday stick-on padding for cases and handlesOutdoor, boat and premium stick-on padding

If the sheet must breathe rather than stick, the product changes: our neoprene perforated foam sheets let air through for breathable supports, and an adhesive-backed sheet and a perforated sheet are ordered from different sheets.

 

Who is neoprene adhesive-backed foam sheets for — and who is it not for?

Equipment makers — adhesive-backed sheets in your colours, cut to your panel sizes, for padding that must stay put.

Case makers — a sticky back for padding glued inside cases, made to your thickness, for products where stitching will not do.

Sports brands — fabric in your colours for the pads you sell, made to fit your range exactly.

Workshops — adhesive-backed sheets for work surfaces and handles, so tools and hands stay protected.

When neoprene is NOT the right choice

  • If the pad must be removed and reused — adhesive holds once, and a hook-and-loop pad suits a removable brief better than a sticky back.
  • If the surface is oily or dusty — adhesive will not bond to a dirty surface, and the surface must be cleaned first.
  • If the sheet is only for a lining — a thinner, lighter sheet fits a lining brief better than a 3 mm adhesive-backed sheet.
  • If the lowest possible unit cost is the whole brief — a plain foam sheet fits a one-season budget better than an adhesive-backed sheet.

 

Customisation Options

Tell us which of these your adhesive-backed foam sheets needs.

  • Adhesive strength: standard or strong adhesive to your drawing, coated evenly on the back.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: 2 mm, 3 mm or 5 mm, split to your order.
  • Foam grade: SBR, SCR or CR foam, to your design.
  • Sheet size: cut to your panel size, or supplied as full sheets with release paper.
  • Packaging: flat sheets as standard; rolls on request.

 

Frequently Asked Questions

Will the adhesive hold on my surface?
Yes, if the surface is right. The adhesive holds on metal, plastic and wood, and the release paper peels off cleanly — tell us the surface material and we check the bond on the sample.

Can the pad be removed and stuck again?
Not really. Adhesive holds once, and peeling it off weakens the bond — if the pad must be removed and reused, tell us and we will suggest a hook-and-loop face instead.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We supply adhesive-backed foam sheets to your thickness, your print and your size, and we check the the bond on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom adhesive-backed foam sheets and we will confirm the best foam grade and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The surfaces the sheets stick to
  3. The thickness you need
  4. Foam grade — SBR, SCR or CR
  5. Print and colours
  6. Packaging — flat sheets or rolls

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

An adhesive-backed sheet is judged on the surface, not on a roll. Send us the surface size and we will make you a sample sheet to cut.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.