NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Sherpa Fabric
  • Neoprene Sherpa Fabric
  • Neoprene Sherpa Fabric
Neoprene Sherpa FabricNeoprene Sherpa FabricNeoprene Sherpa Fabric

Neoprene Sherpa Fabric

Neoprene sherpa fabric is laminated neoprene (SBR, SCR or CR foam + a sherpa face), usually 5 mm thick, with a deep, soft pile like sheep's wool, for winter coats and warm linings that must feel warm the moment they are put on. Coat makers, winter brands and lining makers order it for the inner or outer face of products where warmth is the point. Coat makers buy it as sherpa sheets and cut it to their pattern; it is not a finished coat. Send us your design drawing, the products the fabric is cut for and the thickness, and we will confirm the best foam grade and thickness for winter coats and warm linings.

We make sherpa fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the sherpa face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.

A sherpa face has to feel deep and warm, so the pile matters more than the colour. We laminate the sherpa face to the foam under heat and pressure, so the face does not peel at the cut edge, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The sherpa pile feels soft and deep on the skin, so a winter coat feels warm before it is even fastened.

The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and wastes less than a roll that curls at the edges. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for outdoor use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a coat panel from it and stitching it, because a face that sheds at the seam is a face that ends up in the offcut bin.

 

What thickness of neoprene is best for sherpa fabric?

5 mm is the standard for most sherpa fabric. It gives a good balance of warmth, a deep pile and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.

3 mmLight winter coats and warm linings for cool daysLeast warmth; not enough for a cold winter
5 mmMost sherpa fabric; winter coats and warm liningsBest balance of warmth, a deep pile and an easy sew
7 mmVery cold winters, heavy coats and linings that must insulateWarmest, but heavier and slower to dry

Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the warmth the finished product needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and leaves no room for the seam, or covers the seam and pulls short at the edge. See our custom sherpa fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene quilted fabric face rather than a sherpa fabric face, see our neoprene quilted fabric.

 

SBR or CR neoprene — which is right for sherpa fabric?

SBR is the standard foam under a sherpa face, and CR is the choice where the finished product will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a winter coat or warm lining used indoors or on land. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a winter coat or lining sold for outdoor wear and cold weather.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the wearer without a fight; SBR is firmer and holds a coat's shape when it is hung up to dry.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday winter coats and warm liningsOutdoor and premium winter coats and linings

If the face needs a fleece pile rather than a sherpa pile, the product changes: our neoprene fleece fabric feel warm and soft for winter wetsuits and coats, and a sherpa face and a fleece face are ordered from different sheets.

 

Who is neoprene sherpa fabric for — and who is it not for?

Coat makers — sherpa-faced sheets in your colours, cut to your panel sizes, for winter coats that feel warm at once.

Winter brands — fabric in your colours for the warm goods you sell, made to fit your range exactly.

Lining makers — a deep pile for warm linings, made to your thickness, for products where warmth is the point.

Gift companies — sherpa-faced sheets for branded winter goods, so your client's name feels at home on a warm product.

When neoprene is NOT the right choice

  • If the finished product is for summer — a nylon or lycra face suits a summer brief better than a sherpa face.
  • If the face must be waterproof — a smooth skin face resists water better than a sherpa face.
  • If the fabric is only for a lining — a thinner, lighter face fits a lining brief better than a 5 mm laminated sheet.
  • If the lowest possible unit cost is the whole brief — an unlaminated foam sheet fits a one-season budget better than a sherpa-faced sheet.

 

Customisation Options

Tell us which of these your sherpa fabric needs.

  • Print: screen print for spot logos on the sherpa face, where the pile allows it.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: 3 mm, 5 mm or 7 mm, split to your order.
  • Foam grade: SBR, SCR or CR foam under the face, to your design.
  • Sheet size: cut to your panel size, or supplied as full sheets.
  • Packaging: flat sheets as standard; rolls on request.

 

Frequently Asked Questions

Is the sherpa pile warm on the skin?
Yes. The sherpa pile feels soft and deep on the skin, so a winter coat feels warm before it is even fastened — tell us the product and we check the warmth on the sample.

Will the sherpa shed at the seam?
Not if the lamination is right. We laminate the sherpa face to the foam under heat and pressure, so the face does not shed at the cut edge — tell us the product and we check the lamination on the sample.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We supply sherpa fabric to your thickness, your print and your size, and we check the the warmth on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom sherpa fabric and we will confirm the best foam grade and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The finished products the fabric is cut for
  3. The thickness you need
  4. Foam grade — SBR, SCR or CR
  5. Print and colours
  6. Packaging — flat sheets or rolls

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A sherpa face is judged on the skin, not on a roll. Send us the product size and we will make you a sample sheet to cut.

PREVIOUS:Neoprene Quilted Fabric No next

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.