NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Fleece Fabric
  • Neoprene Fleece Fabric
  • Neoprene Fleece Fabric
Neoprene Fleece FabricNeoprene Fleece FabricNeoprene Fleece Fabric

Neoprene Fleece Fabric

Neoprene fleece fabric is laminated neoprene (SBR, SCR or CR foam + a fleece face), usually 5 mm thick, that feels warm and soft on the skin, for winter wetsuits, coats and warm goods that must insulate against the cold. Wetsuit makers, coat makers and winter brands order it for the inner or outer face of products where warmth is the point. Wetsuit and coat makers buy it as sheets and cut it to their pattern; it is not a finished wetsuit. Send us your design drawing, the products the fabric is cut for and the thickness, and we will confirm the best foam grade and thickness for winter wetsuits, coats and warm goods.

We make fleece fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the fleece face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.

A fleece face has to feel warm, so the pile matters more than the colour. We laminate the fleece face to the foam under heat and pressure, so the face does not peel at the cut edge, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The fleece face feels soft and warm on the skin, so a winter wetsuit slides on without the cold shock of a smooth face.

The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and wastes less than a roll that curls at the edges. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a wetsuit panel from it and stitching it, because a face that sheds at the seam is a face that ends up in the offcut bin.

 

What thickness of neoprene is best for fleece fabric?

5 mm is the standard for most fleece fabric. It gives a good balance of warmth, a soft hand and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.

3 mmLight winter wetsuits, coats and warm goods for cool daysLeast warmth; not enough for a cold winter
5 mmMost fleece fabric; winter wetsuits, coats and warm goodsBest balance of warmth, a soft hand and an easy sew
7 mmVery cold winters, heavy coats and warm goods that must insulateWarmest, but heavier and slower to dry

Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the warmth the finished product needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and leaves no room for the seam, or covers the seam and pulls short at the edge. See our custom fleece fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene glitter fabric face rather than a fleece fabric face, see our neoprene glitter fabric.

 

SBR or CR neoprene — which is right for fleece fabric?

SBR is the standard foam under a fleece face, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a winter wetsuit, coat or warm product used on land or in a pool. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a winter wetsuit or coat sold for the sea, the beach and cold-water use.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the body without a fight; SBR is firmer and holds a coat's shape when it is hung up to dry.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday winter wetsuits, coats and warm goodsSea, beach and premium winter wetsuits and coats

If the face needs a sherpa pile rather than a fleece pile, the product changes: our neoprene sherpa fabric feel deeper and warmer for winter coats and linings, and a fleece face and a sherpa face are ordered from different sheets.

 

Who is neoprene fleece fabric for — and who is it not for?

Wetsuit makers — fleece-faced sheets in your colours, cut to your panel sizes, for winter wetsuits that feel warm on the skin.

Coat makers — a warm face for winter coats, made to your thickness, for products where warmth is the point.

Winter brands — fabric in your colours for the warm goods you sell, made to fit your range exactly.

Print shops — fleece-faced sheets that take print well, so your artwork stays bright after months of use.

When neoprene is NOT the right choice

  • If the finished product is for summer — a nylon or lycra face suits a summer brief better than a fleece face.
  • If the face must be waterproof — a smooth skin face resists water better than a fleece face.
  • If the fabric is only for a lining — a thinner, lighter face fits a lining brief better than a 5 mm laminated sheet.
  • If the lowest possible unit cost is the whole brief — an unlaminated foam sheet fits a one-season budget better than a fleece-faced sheet.

 

Customisation Options

Tell us which of these your fleece fabric needs.

  • Print: screen print for spot logos on the fleece face, where the pile allows it.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: 3 mm, 5 mm or 7 mm, split to your order.
  • Foam grade: SBR, SCR or CR foam under the face, to your design.
  • Sheet size: cut to your panel size, or supplied as full sheets.
  • Packaging: flat sheets as standard; rolls on request.

 

Frequently Asked Questions

Is the fleece face warm on the skin?
Yes. The fleece face feels soft and warm on the skin, so a winter wetsuit slides on without the cold shock of a smooth face — tell us the product and we check the warmth on the sample.

Will the fleece shed at the seam?
Not if the lamination is right. We laminate the fleece face to the foam under heat and pressure, so the face does not shed at the cut edge — tell us the product and we check the lamination on the sample.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We supply fleece fabric to your thickness, your print and your size, and we check the the warmth on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom fleece fabric and we will confirm the best foam grade and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The finished products the fabric is cut for
  3. The thickness you need
  4. Foam grade — SBR, SCR or CR
  5. Print and colours
  6. Packaging — flat sheets or rolls

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A fleece face is judged on the skin, not on a roll. Send us the product size and we will make you a sample sheet to cut.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.