A neoprene phone sleeve is a soft pouch made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 3 mm thick, that holds one phone to protect the screen and body against scratches and knocks. Phone accessory brands, gift shops and travel stores order it for phones and daily carry, because it slides into a pocket or a bag and costs far less than a hard case. It holds one phone only. Send us your design drawing and phone size, and we will confirm the best material and thickness for phones and daily carry.
We manufacture custom neoprene phone sleeves in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished phone sleeve under one roof, so a change to the fit or the closure can be checked on a sample before bulk production starts.
A phone sleeve is judged by the phone sliding in and out cleanly, so the opening matters more than the print. We cut the sleeve to the phone size with a soft fabric face inside, so the screen slides in without catching, and the foam outside cushions the phone against knocks in a bag. The opening is commonly a slip-in top, a fold-over flap or a zip to your drawing, and the zip is placed so its teeth never touch the screen when the sleeve is opened and closed.
3 mm is the standard for most phone sleeves. It gives a good balance of scratch protection, cushioning and a slim sleeve that still fits in a pocket, which is why most of the phone sleeves we make are cut in 3 mm. For the full range, see our neoprene sheet thickness guide.
| 3 mm | Most phone sleeves; daily carry in a pocket or a bag | Best balance of protection and a slim fit |
|---|---|---|
| 5 mm | Phones carried in a busy bag or a toolbox; extra cushioning | More protection, but thicker and less pocket-friendly |
| 7 mm | Expensive phones and rough travel use | Most cushioning, but bulky for everyday carry |
Measure the phone, not the sleeve you already own. Measure the full height, width and thickness of the phone with its case off, and tell us whether the phone has a raised camera: a sleeve ordered by phone name alone often fits the body and presses on the camera, or fits the camera and gaps at the sides. See our custom phone sleeves — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a sleeve cut for a tablet rather than a phone, our neoprene tablet sleeves are the closer page.
SBR is the standard choice for most phone sleeves, and CR is the choice where the sleeve will live outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a sleeve carried in a bag, a pocket or a car. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a sleeve sold with beach gear or left in the sun.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the phone without a fight; SBR is firmer and holds the sleeve flat and neat in a pocket. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday phone sleeves for bags and pockets | Beach, outdoor and premium phone sleeves |
If the phone needs a hard shell rather than a soft sleeve, the product changes: Our neoprene phone cases are cut from the same laminated neoprene, and the two are ordered from different patterns.
Phone accessory brands — a sleeve printed with your logo that fits the phones you sell, made to your exact phone sizes.
Gift companies — a branded sleeve as a corporate gift or a promotional item, in your colours, for conferences and welcome packs.
Travel stores — sleeves for phones carried on holiday, where a hard case is heavy and a soft sleeve slips into a pocket.
Online gadget stores — a sleeve that photographs well, ships flat and fits the most popular phone sizes, for customers who buy phone care online.
When neoprene is NOT the right choice
Tell us which of these your phone sleeve needs, and we will build the sample to your drawing.
Will the sleeve fit my phone with its case on?
Tell us before we cut. A sleeve is cut to the phone with its case off as standard, and we can cut it larger for a cased phone — send the phone height, width and thickness with the case on and we will size it to that.
Can I add a card pocket to the sleeve?
Yes. A small front pocket for one or two cards can be added where you ask for it, stitched and reinforced at the edges, so the sleeve carries the phone and the cards a customer needs for a quick trip out.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the phone size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom phone sleeves to your drawing, your size and your print, and we check the fit on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom phone sleeves and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A phone sleeve is judged every time the phone goes in and out. Send us the phone size and we will make you a sample to try with a real phone.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.