NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Mesh Fabric
  • Neoprene Mesh Fabric
  • Neoprene Mesh Fabric
Neoprene Mesh FabricNeoprene Mesh FabricNeoprene Mesh Fabric

Neoprene Mesh Fabric

Neoprene mesh fabric is laminated neoprene (SBR, SCR or CR foam + a mesh face), usually 3 mm thick, that lets air through the surface, for breathable bags, supports and sports gear that must not trap heat and sweat. Sports brands, bag makers and support makers order it for the outer face of products worn close to the body or carried in hot weather. It comes as flat sheets for support makers to cut, not as a finished support. Send us your design drawing, the products the fabric is cut for and the thickness, and we will confirm the best foam grade and thickness for breathable bags, supports and sports gear.

We make mesh fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the mesh face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.

A mesh face has to breathe, so the lamination matters more than the colour. We laminate the mesh face to the foam under heat and pressure, so the mesh does not peel at the cut edge, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The mesh face feels open on the skin, so a support worn all day does not trap sweat the way a smooth face does.

The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and wastes less than a roll that curls at the edges. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a support panel from it and stitching it, because a mesh that frays at the seam is a mesh that ends up in the offcut bin.

 

What thickness of neoprene is best for mesh fabric?

3 mm is the standard for most mesh fabric. It gives a good balance of airflow, grip and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.

2 mmLight breathable bags, supports and sports gear where airflow matters mostLeast padding; not enough for a product that must also cushion
3 mmMost mesh fabric; breathable bags, supports and sports gearBest balance of airflow, grip and an easy sew
5 mmHeavy supports, work bags and gear that must also protectMost padding, but heavier and slower to dry

Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the airflow the finished product needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and leaves no room for the seam, or covers the seam and pulls short at the edge. See our custom mesh fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene jersey fabric face rather than a mesh fabric face, see our neoprene jersey fabric.

 

SBR or CR neoprene — which is right for mesh fabric?

SBR is the standard foam under a mesh face, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a breathable bag, support or sports product used on land or indoors. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a breathable product sold for the beach, the sea and hot weather.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the body without a fight; SBR is firmer and holds a bag's shape when it is hung up to dry.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday breathable bags, supports and sports gearBeach, sea and premium breathable gear

If the face needs a smooth surface rather than an open mesh, the product changes: our neoprene nylon fabric sew cleanly for wetsuits and bags, and a mesh face and a nylon face are ordered from different sheets.

 

Who is neoprene mesh fabric for — and who is it not for?

Sports brands — mesh-faced sheets in your colours, cut to your panel sizes, for supports and gear that must breathe.

Bag makers — a breathable face for bags carried in hot weather, made to your thickness, for products that must not trap heat.

Support makers — mesh-faced sheets for braces and supports worn all day, so the skin stays dry.

Outdoor brands — fabric in your colours for the gear you sell, made to fit your range exactly.

When neoprene is NOT the right choice

  • If the finished product must keep water out — a smooth face resists splashes better than an open mesh face.
  • If the face must take a print — a nylon or polyester face takes print better than a mesh face.
  • If the fabric is only for a lining — a thinner, lighter face fits a lining brief better than a 3 mm laminated sheet.
  • If the lowest possible unit cost is the whole brief — an unlaminated foam sheet fits a one-season budget better than a mesh-faced sheet.

 

Customisation Options

Tell us which of these your mesh fabric needs.

  • Print: screen print for spot logos on the mesh face, where the mesh allows it.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: 2 mm, 3 mm or 5 mm, split to your order.
  • Foam grade: SBR, SCR or CR foam under the face, to your design.
  • Sheet size: cut to your panel size, or supplied as full sheets.
  • Packaging: flat sheets as standard; rolls on request.

 

Frequently Asked Questions

Will the mesh face fray at the cut edge?
No, not if the lamination is right. We laminate the mesh face to the foam under heat and pressure, so the mesh does not peel or fray at the cut edge — tell us the product and we check the lamination on the sample.

Does the mesh really let air through?
Yes. The mesh face is open, so air passes through the surface and a support worn all day does not trap sweat the way a smooth face does — tell us the product and we check the airflow on the sample.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We supply mesh fabric to your thickness, your print and your size, and we check the the airflow on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom mesh fabric and we will confirm the best foam grade and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The finished products the fabric is cut for
  3. The thickness you need
  4. Foam grade — SBR, SCR or CR
  5. Print and colours
  6. Packaging — flat sheets or rolls

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A mesh face is judged on the body, not on a roll. Send us the product size and we will make you a sample sheet to cut.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.