Neoprene camouflage fabric is laminated neoprene (SBR, SCR or CR foam + a camouflage-printed face), usually 3 mm thick, that carries a camo pattern across the whole surface, for hunting, fishing and outdoor gear that must blend into the field, the forest or the water. Hunting brands, fishing brands and outdoor makers order it for the outer face of waders, bags and covers where the pattern is the point. Hunting and fishing makers buy it as camo sheets and cut it to their pattern; it is not finished gear. Send us your design drawing, the products the fabric is cut for and the camo pattern, and we will confirm the best foam grade and thickness for hunting, fishing and outdoor gear.
We make camouflage fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the camouflage face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.
A camouflage face has to stay sharp, so the print step matters more than the colour. We print the camo pattern on the face before lamination, so the pattern does not crack when the foam is cut and sewn, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The pattern can be woodland, marsh or digital camo, and the colours stay bright after months outdoors.
The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and keeps the pattern lined up across panels. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for water use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a wader panel from it and stitching it, because a pattern that cracks at the seam is a pattern that ends up in the offcut bin.
3 mm is the standard for most camouflage fabric. It gives a good balance of pattern, concealment and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.
| 2 mm | Light hunting and fishing gear where weight matters | Least padding; not enough for a product that must also cushion |
|---|---|---|
| 3 mm | Most camouflage fabric; hunting, fishing and outdoor gear | Best balance of pattern, concealment and an easy sew |
| 5 mm | Heavy outdoor gear, waders and products that take a beating | Most padding, but heavier and stiffer to cut and sew |
Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the pattern repeat the artwork needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and cuts the pattern in half, or fits the pattern and pulls short at the edge. See our custom camouflage fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene mesh fabric face rather than a camouflage fabric face, see our neoprene mesh fabric.
SBR is the standard foam under a camouflage face, and CR is the choice where the finished product will live in water. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for hunting or fishing gear used on land or in a boat. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for waders, fishing gear and outdoor products sold for the water and the shore.
Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the wearer without a fight; SBR is firmer and holds a bag's shape when it is hung up to dry.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday hunting, fishing and outdoor gear | Water, shore and premium hunting and fishing gear |
If the face needs a plain surface rather than a camo pattern, the product changes: our neoprene polyester fabric take daily wear better for bags and covers, and a camouflage face and a polyester face are ordered from different sheets.
Hunting brands — camo-faced sheets in your pattern, cut to your panel sizes, for gear that blends into the field.
Fishing brands — fabric printed with your camo for the waders and bags you sell, made to fit your range exactly.
Outdoor makers — a camo face for outdoor gear, made to your thickness, for products where the pattern is the point.
Print shops — camo-faced sheets that keep the pattern sharp across panels, so your print work looks its best on the finished product.
When neoprene is NOT the right choice
Tell us which of these your camouflage fabric needs.
Will the camo pattern crack at the seam?
No, not if the print is done right. We print the camo pattern on the face before lamination, so the pattern does not crack when the foam is cut and sewn — send the pattern and we check the print on the sample.
Can you print our own camo pattern?
Yes. We print your own camo pattern by sublimation for full-colour artwork, in woodland, marsh or digital styles — send the artwork with your drawing and we confirm the print before sampling.
What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We supply camouflage fabric to your thickness, your print and your size, and we check the the pattern on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom camouflage fabric and we will confirm the best foam grade and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A camo face is judged in the field, not on a roll. Send us the pattern and we will make you a sample sheet to cut.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.