NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Nylon Fabric
  • Neoprene Nylon Fabric
  • Neoprene Nylon Fabric
Neoprene Nylon FabricNeoprene Nylon FabricNeoprene Nylon Fabric

Neoprene Nylon Fabric

Neoprene nylon fabric is laminated neoprene (SBR, SCR or CR foam + a nylon face), usually 3 mm thick, that gives wetsuits, bags and outdoor gear a tough, smooth outside that sews cleanly and dries fast. Wetsuit makers, bag makers and outdoor brands order it for the outer face of the products they cut, because nylon takes print well and stands up to daily use. Makers buy it as flat sheets and cut it to their own pattern; it is not sold as a finished wetsuit or bag. Send us your design drawing, the products the fabric is cut for and the thickness, and we will confirm the best foam grade and thickness for wetsuits, bags and outdoor gear.

We make nylon fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the nylon face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.

A nylon face has to sew cleanly, so the lamination matters more than the colour. We laminate the nylon face to the foam under heat and pressure, so the face does not peel at the cut edge, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The nylon face takes sublimation print well, so a wetsuit maker's artwork stays bright after months in the sea.

The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and wastes less than a roll that curls at the edges. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a wetsuit panel from it and stitching it, because a face that frays at the seam is a face that ends up in the offcut bin.

 

What thickness of neoprene is best for nylon fabric?

3 mm is the standard for most nylon fabric. It gives a good balance of strength, stretch and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.

2 mmLight wetsuits, bags and linings where weight mattersLeast padding; not enough for a cold-water wetsuit
3 mmMost nylon fabric; wetsuits, bags and outdoor gearBest balance of strength, stretch and an easy sew
5 mmCold-water wetsuits, heavy bags and outdoor gear that takes a beatingMost padding, but heavier and stiffer to cut and sew

Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the thickness the finished product needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and leaves no room for the seam, or covers the seam and pulls short at the edge. See our custom nylon fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene lycra fabric face rather than a nylon fabric face, see our neoprene lycra fabric.

 

SBR or CR neoprene — which is right for nylon fabric?

SBR is the standard foam under a nylon face, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a wetsuit, bag or outdoor product used on land or in a pool. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a wetsuit or bag sold for the sea, the beach and daily salt-water use.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the body without a fight; SBR is firmer and holds a bag's shape when it is hung up to dry.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday wetsuits, bags and outdoor gearSea, beach and premium wetsuits and bags

If the face needs more stretch than nylon gives, the product changes: our neoprene lycra fabric stretch further for swimwear and surf suits, and a nylon face and a lycra face are ordered from different sheets.

 

Who is neoprene nylon fabric for — and who is it not for?

Wetsuit makers — nylon-faced sheets in your colours, cut to your panel sizes, for wetsuits that sew cleanly and dry fast.

Bag makers — a tough face for bags and outdoor gear, made to your thickness, for products that take daily use.

Outdoor brands — fabric printed with your logo for the gear you sell, made to fit your range exactly.

Print shops — nylon-faced sheets that take sublimation print well, so your artwork stays bright after months of use.

When neoprene is NOT the right choice

  • If the finished product needs a soft hand feel — a jersey face suits a soft brief better than a nylon face.
  • If the face must stretch a long way — a lycra or spandex face stretches further than a nylon face.
  • If the fabric is only for a lining — a thinner, lighter face fits a lining brief better than a 3 mm laminated sheet.
  • If the lowest possible unit cost is the whole brief — an unlaminated foam sheet fits a one-season budget better than a nylon-faced sheet.

 

Customisation Options

Tell us which of these your nylon fabric needs.

  • Print: sublimation for full-colour artwork, screen print for spot logos, on the nylon face.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: 2 mm, 3 mm or 5 mm, split to your order.
  • Foam grade: SBR, SCR or CR foam under the face, to your design.
  • Sheet size: cut to your panel size, or supplied as full sheets.
  • Packaging: flat sheets as standard; rolls on request.

 

Frequently Asked Questions

Will the nylon face peel at the cut edge?
No, not if the lamination is right. We laminate the nylon face to the foam under heat and pressure, so the face does not peel at the cut edge — tell us the product and we check the lamination on the sample.

Can the face be printed with our artwork?
Yes. The nylon face takes sublimation print well, so your artwork stays bright after months in the sea — send the artwork with your drawing and we confirm the print before sampling.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We supply nylon fabric to your thickness, your print and your size, and we check the the face on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom nylon fabric and we will confirm the best foam grade and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The finished products the fabric is cut for
  3. The thickness you need
  4. Foam grade — SBR, SCR or CR
  5. Print and colours
  6. Packaging — flat sheets or rolls

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A nylon face is judged on the cutting table, not on a roll. Send us the product size and we will make you a sample sheet to cut.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.