Neoprene printed fabric is laminated neoprene (SBR, SCR or CR foam + a printed face), usually 3 mm thick, that carries a brand's artwork, pattern or logo across the whole surface, for branded bags, sleeves and promos that must be recognised at a glance. Gift brands, bag makers and promo suppliers order it for products where the print is the point, because the face is printed before lamination so the artwork stays sharp. Bag makers buy it as printed sheets and cut it to their pattern; it is not a finished bag. Send us your design drawing, the products the fabric is cut for and the artwork, and we will confirm the best foam grade and thickness for branded bags, sleeves and promos.
We make printed fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the printed face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.
A printed face has to stay sharp, so the print step matters more than the colour. We print the face before lamination, so the artwork does not crack when the foam is cut and sewn, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The print can be a full-colour photograph, a repeat pattern or a single logo, and the colours stay bright after months of use.
The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and keeps the print lined up across panels. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a bag panel from it and stitching it, because a print that cracks at the seam is a print that ends up in the offcut bin.
3 mm is the standard for most printed fabric. It gives a good balance of print clarity, colour and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.
| 2 mm | Light branded bags, sleeves and promos where weight matters | Least padding; not enough for a product that must also cushion |
|---|---|---|
| 3 mm | Most printed fabric; branded bags, sleeves and promos | Best balance of print clarity, colour and an easy sew |
| 5 mm | Heavy branded bags and promos that must also protect | Most padding, but heavier and slower to dry |
Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the print area the artwork needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and cuts the artwork in half, or fits the artwork and pulls short at the edge. See our custom printed fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene polyester fabric face rather than a printed fabric face, see our neoprene polyester fabric.
SBR is the standard foam under a printed face, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a branded bag, sleeve or promo used on land or in a pool. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a branded bag or sleeve sold for the beach and daily salt-water use.
Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the product without a fight; SBR is firmer and holds a bag's shape when it is hung up to dry.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday branded bags, sleeves and promos | Beach, sea and premium branded bags and sleeves |
If the face needs a plain hard-wearing surface rather than a print, the product changes: our neoprene polyester fabric take daily wear better for bags and covers, and a printed face and a polyester face are ordered from different sheets.
Gift brands — printed sheets in your artwork, cut to your panel sizes, for promos that are recognised at a glance.
Bag makers — a printed face for branded bags, made to your thickness, for products where the print is the point.
Promo suppliers — fabric printed with your client's logo for the promos you supply, made to fit your range exactly.
Print shops — printed sheets that keep artwork sharp across panels, so your print work looks its best on the finished product.
When neoprene is NOT the right choice
Tell us which of these your printed fabric needs.
Will the print crack at the seam?
No, not if the print is done right. We print the face before lamination, so the artwork does not crack when the foam is cut and sewn — send the artwork and we check the print on the sample.
Can you print a full-colour photograph?
Yes. The face takes sublimation print for full-colour artwork, including photographs and repeat patterns — send the artwork with your drawing and we confirm the print before sampling.
What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We supply printed fabric to your thickness, your print and your size, and we check the the print on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom printed fabric and we will confirm the best foam grade and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A printed face is judged on the finished bag, not on a roll. Send us the artwork and we will make you a sample sheet to cut.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.