A neoprene game controller case is a padded case made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 5 mm thick, that holds one game controller in moulded compartments to protect the sticks and buttons against knocks. Gaming shops, electronics brands and gift companies order it for game controllers and gaming gear, because it keeps the sticks from snapping in a bag and carries in one hand. It holds one controller only. Send us your design drawing, the controller size and the case style, and we will confirm the best material and thickness for game controllers and gaming gear.
We manufacture custom neoprene game controller cases in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished game controller case under one roof, so a change to the controller size or the compartments can be checked on a sample before bulk production starts.
A controller case is judged by the sticks, so the compartments matter more than the print. We cut the case to the controller size with moulded compartments that hold the sticks and the body apart, so the sticks do not press against the case wall in a bag, and the zip is placed so its teeth never touch the controller when the case is opened and closed. The whole case wipes clean after a gaming session, and the foam outside cushions the controller against knocks.
5 mm is the standard for most game controller cases. It gives a good balance of padding, a firm shape and a case that still packs flat, which is why most of the game controller cases we make are cut in 5 mm. For the full range, see our neoprene sheet thickness guide.
| 3 mm | Light controller cases for a short carry and for daily use | Least padding; not enough for a controller thrown in a bag |
|---|---|---|
| 5 mm | Most game controller cases; travel and daily gaming | Best balance of padding, a firm shape and a packable fit |
| 7 mm | Premium controller cases and cases for rough travel | Most padding, but heavier to carry by hand |
Measure the controller, not the case you already own. Measure the full width, height and thickness of the controller with the sticks on, and tell us the stick height: a case ordered by controller name alone often fits the body and presses on the sticks, or fits the sticks and gaps at the sides. See our custom game controller cases — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a case cut for headphones rather than a case cut for a controller, our neoprene headphone cases are the closer page.
SBR is the standard choice for most game controller cases, and CR is the choice where the case will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a case used at home or on the move. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a case sold with outdoor gear or left in the sun.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the controller compartments without a fight; SBR is firmer and holds the case firm and square in a bag. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday game controller cases for home and travel | Outdoor and premium game controller cases |
If the headset needs a case rather than the controller, the shape changes: Our neoprene VR headset cases are cut from the same laminated neoprene, and the two are ordered from different patterns.
Gaming shops — cases in your colours for the controllers you sell, made to fit your controller sizes exactly.
Electronics brands — a case printed with your logo that gamers carry to every session, made to your design.
Gift companies — a branded controller case as a gift for gamers, in your colours, for birthdays and holidays.
Esports teams — cases in team colours for players, so the team name travels with the controller.
When neoprene is NOT the right choice
Tell us which of these your game controller case needs, and we will build the sample to your drawing.
Will the sticks press against the case wall?
No, not if the compartments are cut right. The moulded compartments hold the sticks away from the wall, so the sticks do not snap in a bag — send the stick height with your drawing and we will cut the compartments to it.
Can the case hold a controller and a headset?
Tell us both sizes before we cut. A case for a controller alone is cut differently from a case for a controller and a headset — we can make one larger case with two compartments, and we will confirm the size for both.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the controller size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom game controller cases to your drawing, your size and your print, and we check the compartments and the fit on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom game controller cases and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A controller case is judged by sticks arriving unbroken. Send us the controller size and we will make you a sample to try with a real controller.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.