A neoprene e-reader sleeve is a soft pouch made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 3 mm thick, that holds one e-reader to protect the screen against scratches and knocks. Book shops, electronics brands and gift companies order it for e-readers and daily reading, because it slides into a bag and costs far less than a hard case. It holds one e-reader only. Send us your design drawing and e-reader size, and we will confirm the best material and thickness for e-readers and daily reading.
We manufacture custom neoprene e-reader sleeves in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished e-reader sleeve under one roof, so a change to the fit or the closure can be checked on a sample before bulk production starts.
An e-reader sleeve is judged by the screen, so the inside matters more than the outside. We cut the sleeve to the e-reader size with a soft fabric face inside, so the screen slides in without catching, and the foam outside cushions the device against knocks in a bag. The opening is commonly a slip-in top or a fold-over flap to your drawing, and the seams are placed at the sides where they do not press on the screen.
3 mm is the standard for most e-reader sleeves. It gives a good balance of scratch protection, cushioning and a slim sleeve that still fits in a bag, which is why most of the e-reader sleeves we make are cut in 3 mm. For the full range, see our neoprene sheet thickness guide.
| 3 mm | Most e-reader sleeves; daily reading in a bag | Best balance of protection and a slim fit |
|---|---|---|
| 5 mm | E-readers carried in a busy bag or a toolbox; extra cushioning | More protection, but thicker and less pocket-friendly |
| 7 mm | Expensive e-readers and rough travel use | Most cushioning, but bulky for everyday carry |
Measure the e-reader, not the sleeve you already own. Measure the full height, width and thickness of the e-reader, and tell us whether it has a raised bezel: a sleeve ordered by e-reader name alone often fits the body and presses on the screen, or fits the screen and gaps at the sides. See our custom e-reader sleeves — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a sleeve cut for a tablet rather than an e-reader, our neoprene tablet sleeves are the closer page.
SBR is the standard choice for most e-reader sleeves, and CR is the choice where the sleeve will live outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a sleeve carried in a bag or on a commute. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a sleeve sold with beach gear or left in the sun.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the e-reader without a fight; SBR is firmer and holds the sleeve flat and neat in a bag. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday e-reader sleeves for bags and commutes | Beach, outdoor and premium e-reader sleeves |
If the reader needs a hard shell rather than a soft sleeve, the product changes: Our neoprene laptop sleeves are cut from the same laminated neoprene, and the two are ordered from different patterns.
Book shops — a sleeve printed with your logo for the readers you sell, made to fit your e-reader sizes exactly.
Electronics brands — a sleeve in your colours for your own e-reader line, made to your exact device size.
Gift companies — a branded sleeve as a corporate gift or a reading gift, in your colours.
Online gadget stores — a sleeve that photographs well, ships flat and fits the most popular e-reader sizes, for customers who buy reader care online.
When neoprene is NOT the right choice
Tell us which of these your e-reader sleeve needs, and we will build the sample to your drawing.
Will the sleeve fit my e-reader with its cover on?
Tell us before we cut. A sleeve is cut to the e-reader with its cover off as standard, and we can cut it larger for a covered reader — send the height, width and thickness with the cover on and we will size it to that.
Can I add a pocket for the charging cable?
Yes. A small front pocket for a charging cable can be added where you ask for it, stitched and reinforced at the edges, so the sleeve carries the reader and the cable a customer needs for a trip.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the e-reader size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom e-reader sleeves to your drawing, your size and your print, and we check the fit on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom e-reader sleeves and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
An e-reader sleeve is judged every time the reader goes in and out. Send us the device size and we will make you a sample to try with a real e-reader.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.