NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Wetsuits

  • Neoprene Dive Mask Cases
  • Neoprene Dive Mask Cases
  • Neoprene Dive Mask Cases
Neoprene Dive Mask CasesNeoprene Dive Mask CasesNeoprene Dive Mask Cases

Neoprene Dive Mask Cases

A neoprene dive mask case is a padded case made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 5 mm thick, that holds one dive mask and its snorkel to protect the glass against scratches and knocks. Dive shops, dive brands and gift companies order it for dive masks and snorkelling gear, because the glass scratches easily and the case keeps it safe in a dive bag. It holds one mask only, with room for a snorkel. Send us your design drawing, the mask size and the case style, and we will confirm the best material and thickness for dive masks and snorkelling gear.

We manufacture custom neoprene dive mask cases in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished dive mask case under one roof, so a change to the mask size or the snorkel pocket can be checked on a sample before bulk production starts.

A dive mask case is judged by the glass, so the inside matters more than the outside. We cut the case to the mask size with a soft fabric face inside, so the glass sits without catching, and the padded shell follows the mask shape so the case does not press on the lenses. The snorkel sits in its own pocket where you ask for it, so it does not press on the glass, and the whole case wipes clean after a dive.

 

What thickness of neoprene is best for a dive mask case?

5 mm is the standard for most dive mask cases. It gives a good balance of padding, a firm shape and a case that still packs well, which is why most of the dive mask cases we make are cut in 5 mm. For the full range, see our neoprene sheet thickness guide.

3 mmLight dive mask cases for a short carry and for daily useLeast padding; not enough for a mask thrown in a dive bag
5 mmMost dive mask cases; dive trips and snorkellingBest balance of padding, a firm shape and a packable fit
7 mmPremium dive mask cases and cases for rough travelMost padding, but heavier to carry in a dive bag

Measure the mask, not the case you already own. Measure the full height and width of the mask with the strap on, and the snorkel length, and send both with your enquiry: a case ordered by mask name alone often fits the mask and presses on the lenses, or fits the lenses and gaps at the sides. See our custom dive mask cases — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a case cut for a dive computer rather than a case cut for a dive mask, our neoprene dive computer cases are the closer page.

 

SBR or CR neoprene — which is right for dive mask cases?

SBR is the standard choice for most dive mask cases, and CR is the choice where the case will be used in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a case used on a dive boat or at home. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a case sold with dive gear or used in salt water every day.

The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the mask shape without a fight; SBR is firmer and holds the case firm and square in a dive bag. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday dive mask cases for boats and homeSea diving and premium dive mask cases

If the mask strap needs a cover rather than the mask, the shape changes: Our neoprene dive mask strap covers are cut from the same laminated neoprene, and the two are ordered from different patterns.

 

Who is a neoprene dive mask case for — and who is it not for?

Dive shops — dive mask cases in your colours for the masks you sell, made to fit your mask sizes exactly.

Dive brands — a case printed with your logo that divers carry on every trip, made to your design.

Dive schools — cases for your fleet of masks, so the glass survives daily lessons and your name is seen on every case.

Snorkelling operators — cases for rental masks, so the glass survives the season and your name is seen on the beach.

When neoprene is NOT the right choice

  • If the case must hold two masks — a larger case or two cases, not a single-mask case, is the right product.
  • If the mask needs hard drop protection — neoprene cushions knocks, but a hard case protects against a hard fall onto concrete.
  • If the case must be waterproof — neoprene resists splashes, but a dive mask case is not a dry bag and will not keep water out.
  • If the lowest possible unit cost is the whole brief — a thin fabric pouch fits a one-season budget better than a neoprene case.

 

Customisation Options

Tell us which of these your dive mask case needs, and we will build the sample to your drawing.

  • Logo: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Snorkel pocket: room for a snorkel beside the mask, so it does not press on the glass.
  • Strap slot: a slot for the mask strap where you ask for one, so the strap does not bunch.
  • Fabric face: smooth nylon jersey or another fabric face to your design.
  • Packaging: polybag as standard; hangtag and retail packaging on request.

 

Frequently Asked Questions

Will the snorkel fit beside the mask?
Yes, if the pocket is cut right. The snorkel sits in its own pocket away from the glass, so it does not scratch the lenses — send the snorkel length with your drawing and we will cut the pocket to it.

Can I rinse the case after a salt-water dive?
Yes. The whole case wipes clean with fresh water and dries flat, so salt does not build up in the foam — rinse it after the dive and let it dry out of the sun.

What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the mask size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We make custom dive mask cases to your drawing, your size and your print, and we check the fit on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom dive mask cases and we will confirm the best material and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The mask height and width, and the snorkel length
  3. The quantity you need
  4. Thickness or material preference — SBR, SCR or CR
  5. Logo and colours
  6. Packaging — polybag, hangtag or retail packaging

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A dive mask case is judged by glass arriving unscratched. Send us the mask size and we will make you a sample to try with a real dive mask.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.