A neoprene camera lens case is a round padded case made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 5 mm thick, that holds one camera lens to protect the glass against scratches and knocks. Camera shops, photo brands and gift companies order it for camera lenses and photo gear, because the glass scratches easily and the case keeps it safe in a camera bag. It holds one lens only. Send us your design drawing, the lens size and the case style, and we will confirm the best material and thickness for camera lenses and photo gear.
We manufacture custom neoprene camera lens cases in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished camera lens case under one roof, so a change to the lens size or the closure can be checked on a sample before bulk production starts.
A lens case is judged by the glass, so the inside matters more than the outside. We cut the case to the lens size with a soft fabric face inside, so the glass slides in without catching, and the round shape follows the lens barrel so the case does not press on the glass. The zip is placed so its teeth never touch the lens when the case is opened and closed, and the whole case wipes clean after a shoot.
5 mm is the standard for most camera lens cases. It gives a good balance of padding, a round shape and a case that still packs flat, which is why most of the camera lens cases we make are cut in 5 mm. For the full range, see our neoprene sheet thickness guide.
| 3 mm | Light lens cases for a short carry and for daily use | Least padding; not enough for a lens thrown in a camera bag |
|---|---|---|
| 5 mm | Most camera lens cases; shoots and travel | Best balance of padding, a round shape and a packable fit |
| 7 mm | Premium lens cases and cases for rough travel | Most padding, but heavier to carry in a camera bag |
Measure the lens, not the case you already own. Measure the lens length and diameter with the cap on, and tell us whether the lens has a hood: a case ordered by lens name alone often fits the length and presses on the hood, or fits the hood and gaps at the sides. See our custom camera lens cases — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a case cut for a whole camera rather than a case cut for one lens, our neoprene camera cases are the closer page.
SBR is the standard choice for most camera lens cases, and CR is the choice where the case will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a case used in a studio or on a shoot. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a case sold with outdoor gear or left in the sun.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the round lens shape without a fight; SBR is firmer and holds the case firm and round in a camera bag. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday camera lens cases for studios and shoots | Outdoor and premium camera lens cases |
If the tripod needs a case rather than the lens, the shape changes: Our neoprene tripod cases are cut from the same laminated neoprene, and the two are ordered from different patterns.
Camera shops — lens cases in your colours for the lenses you sell, made to fit your lens sizes exactly.
Photo brands — a case printed with your logo that photographers carry on every shoot, made to your design.
Gift companies — a branded lens case as a gift for photographers, in your colours, for birthdays and holidays.
Photo studios — cases for your fleet of lenses, so the glass survives daily use and your name is seen on every case.
When neoprene is NOT the right choice
Tell us which of these your camera lens case needs, and we will build the sample to your drawing.
Will the case fit my lens with its hood on?
Tell us before we cut. A case is cut to the lens with its cap on as standard, and we can cut it larger for a lens with a hood — send the lens length and diameter with the hood on and we will size it to that.
Can I add a loop to hang the case from my camera bag?
Yes. A loop or a clip can be added where you ask for it, stitched and reinforced at the fixing point, so the case hangs from the bag instead of sinking to the bottom.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the lens size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom camera lens cases to your drawing, your size and your print, and we check the fit on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom camera lens cases and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A lens case is judged by glass arriving unscratched. Send us the lens size and we will make you a sample to try with a real lens.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.