A neoprene camera case is a padded bag made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 5 mm thick, that holds a camera to protect it against knocks, scratches and dust. Camera brands and travel shops order it for photographers who carry a camera every day. It is not a hard camera case, so it does not protect against a hard drop onto concrete. Send us your design drawing, the camera size and the case style, and we will confirm the best material and thickness for cameras and travel.
We manufacture custom neoprene camera cases in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished case under one roof, so a change to the fit or the pocket layout can be checked on a sample before bulk production starts.
A camera case has to fit the camera and the lens together, so the inside size matters more than the outside. We cut the case to the camera body and lens length with a few millimetres of clearance, so the camera slides in without catching on the lens hood, and the foam inside cushions the body against knocks in a bag. The opening is commonly a zip along the top, and the zip is placed so its teeth never touch the lens glass when the case is opened and closed.
The case is cut with a flat base so it stands on a desk instead of rolling away, and the seams are placed at the sides where they do not press on the camera. A divider, a small pocket or a shoulder strap can be added where you ask for it, so a spare battery or a memory card travels with the camera, and the whole case wipes clean after a day outdoors. We check the finished case by sliding the real camera in and out several times, because a case that fights the lens is a case that stays at home.
5 mm is the standard for most camera cases. It gives a good balance of cushioning, protection and a case that still fits in a larger bag, which is why most of the cases we make are cut in 5 mm. For the full range, see our neoprene sheet thickness guide.
| 3 mm | Light cases for a compact camera and for cases carried inside another bag | Least cushioning; not enough for a camera carried on its own |
|---|---|---|
| 5 mm | Most camera cases; daily carry and travel | Best balance of cushioning, protection and a bag-friendly fit |
| 7 mm | Large cameras with a long lens and rough travel use | Most cushioning, but heavier and bulkier |
Measure the camera with the lens on, not the body alone. Measure the full length with the lens attached, the width and the height, and tell us whether the lens hood stays on. See our custom camera cases — made to your camera size, 3–8 mm, with zip opening and strap for the styles this thickness choice applies to. For the strap that carries the camera rather than the case, our neoprene camera straps are the matching page.
SBR is the standard choice for most camera cases, and CR is the choice where the case will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a case carried in a bag, a car or a studio. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a case sold for outdoor shooting, beach work or use in the sun.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the camera body without a fight; SBR is firmer and holds the case shape when it is empty on a shelf. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday camera cases for travel and daily carry | Outdoor, beach and premium camera cases |
If the case must hold a drone rather than a camera, the shape changes: our neoprene drone cases are cut to a drone and its arms, and a camera case and a drone case are ordered from different patterns.
Camera brands — a case printed with your logo that travels with the camera you sell, made to fit your camera and lens exactly.
Travel shops — cases for photographers who travel light, sized to the cameras they actually carry, for trips and holidays.
Photographers and studios — cases in your colours for the cameras you use every day, so the gear is protected between shoots and your name is seen on location.
Online camera stores — a case that photographs well, folds flat for shipping and fits a wide range of camera sizes, for customers who buy camera protection online.
When neoprene is NOT the right choice
Tell us which of these your case needs, and we will build the sample to your drawing.
Will it fit my camera with the lens attached?
Yes, if you send the size with the lens on. We make the case to the full length with the lens attached, not the body alone — measure the camera with the lens and the hood, and send all three with your drawing.
Can I add a divider for a spare battery?
Yes. A divider or a small pocket for a battery or a memory card can be added where you ask for it, stitched to the inside so it does not press on the camera body.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and camera size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the camera size with the lens on and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom camera cases to your drawing, your size and your print, and we check the fit on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom camera cases and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A camera case is judged by the camera sliding in cleanly and the lens staying safe. Send us the camera size and we will make you a sample to try with a real camera.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.