A neoprene tripod case is a long slim case made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 5 mm thick, that holds one tripod to protect the legs and the head against scratches and knocks. Camera shops, photo brands and gift companies order it for tripods and photo gear, because a tripod is long and awkward and the case keeps it safe in a car boot. It holds one tripod only. Send us your design drawing, the tripod size and the case style, and we will confirm the best material and thickness for tripods and photo gear.
We manufacture custom neoprene tripod cases in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished tripod case under one roof, so a change to the tripod size or the handles can be checked on a sample before bulk production starts.
A tripod case is judged by the length, so the fit matters more than the print. We cut the case to the tripod length with a slim shape that follows the folded legs, so the tripod slides in without catching, and the shoulder strap is stitched through the foam and bar-tacked at the fixing points, because a strap that pulls away with a full tripod is the first thing a customer notices. The zip runs the full length where you ask for it, so the tripod loads easily.
5 mm is the standard for most tripod cases. It gives a good balance of padding, a slim shape and a case that still carries well, which is why most of the tripod cases we make are cut in 5 mm. For the full range, see our neoprene sheet thickness guide.
| 3 mm | Light tripod cases for a short carry and for daily use | Least padding; not enough for a tripod thrown in a car boot |
|---|---|---|
| 5 mm | Most tripod cases; shoots and travel | Best balance of padding, a slim shape and a comfortable carry |
| 7 mm | Premium tripod cases and cases for rough travel | Most padding, but heavier to carry on the shoulder |
Measure the tripod folded, not the tripod open. Measure the folded length and the widest width of the folded legs, and tell us the head size: a case ordered by tripod name alone often fits the length and presses on the head, or fits the head and gaps at the legs. See our custom tripod cases — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a round case for one lens rather than a long slim case for a tripod, our neoprene camera lens cases are the closer page.
SBR is the standard choice for most tripod cases, and CR is the choice where the case will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a case used in a studio or on a shoot. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a case sold with outdoor gear or left in the sun.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the long case shape without a fight; SBR is firmer and holds the case slim and straight on the shoulder. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday tripod cases for studios and shoots | Outdoor and premium tripod cases |
If the binoculars need a case rather than the tripod, the shape changes: Our neoprene binocular cases are cut from the same laminated neoprene, and the two are ordered from different patterns.
Camera shops — tripod cases in your colours for the tripods you sell, made to fit your tripod sizes exactly.
Photo brands — a case printed with your logo that photographers carry on every shoot, made to your design.
Gift companies — a branded tripod case as a gift for photographers, in your colours, for birthdays and holidays.
Photo studios — cases for your fleet of tripods, so the legs survive daily use and your name is seen on every case.
When neoprene is NOT the right choice
Tell us which of these your tripod case needs, and we will build the sample to your drawing.
Will the case fit my tripod with its head on?
Tell us before we cut. A case is cut to the folded tripod with its head on as standard, and we can cut it wider for a large head — send the folded length, the leg width and the head size and we will size it to that.
Can I carry the tripod case on my shoulder?
Yes. A shoulder strap is stitched through the foam and bar-tacked at the fixing points, so the tripod carries hands-free — tell us the tripod weight and we will fit the strap to it.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the tripod size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom tripod cases to your drawing, your size and your print, and we check the length and the strap on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom tripod cases and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A tripod case is judged by a tripod arriving unscratched. Send us the folded size and we will make you a sample to try with a real tripod.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.