NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene For Bracer

  • Neoprene Shoulder & Posture Support
  • Neoprene Shoulder & Posture Support
  • Neoprene Shoulder & Posture Support
Neoprene Shoulder & Posture SupportNeoprene Shoulder & Posture SupportNeoprene Shoulder & Posture Support

Neoprene Shoulder & Posture Support

A neoprene shoulder and posture support is a slim, stretchy brace made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 3 mm thick, that gives gentle compression and warmth to the shoulder and upper back. Sports shops, health brands and office-wellness sellers order it for desk workers and returning players. It is not a medical brace. Send us your design drawing and size range, and we will confirm the best material and thickness.

We manufacture custom neoprene shoulder and posture supports in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished support under one roof, so a change to the strap layout or the fit can be checked on a sample before bulk production starts.

A shoulder and posture support is worn for hours at a time, often under a shirt, so it has to be slim, soft at the edges and easy to adjust. The panels are cut from laminated neoprene and stitched with flat seams, and the straps are placed so they pull the shoulders back gently without digging in at the armpits — the most common complaint with a badly placed strap.

The fastening is usually adjustable, so the wearer can set the fit in the morning and loosen it later in the day, and the edges are commonly finished with a bound hem so they do not rub the skin under everyday clothing. We cut the strap length with about 2 cm of adjustment range on each side, because a strap that only fits at its very end either slips loose or cannot be tightened at all.

The foam gives gentle compression and warmth around the shoulder and upper back, which helps the wearer hold a straighter posture and feel supported through the day. Because the support is thin and stretchy, it fits under a work shirt or a training top without showing a hard outline, and it can be taken off and put back on without help.

 

What thickness of neoprene is best for a shoulder and posture support?

3 mm is the standard for most shoulder and posture supports. It is slim enough to wear under a shirt all day and flexible enough to sit at a desk in, which is why most of the supports we make are cut in 3 mm. For the full range, see our neoprene sheet thickness guide.

ThicknessBest forTrade-off
3 mmAll-day wear under everyday clothing; desk work and light trainingLeast support; gentle compression only
5 mmWearers who want more warmth and a firmer feelBest balance of support, warmth and a slim fit under a shirt
7 mmThe firmest feel and the most warmthBulkier under clothing; too warm for all-day desk wear

Measure the chest, not the shirt size. Take the chest circumference at armpit level with a soft tape, and tell us the shoulder width as well, because shirt sizes vary between brands and a support ordered by shirt size often pulls tight at the armpit or hangs loose at the back. See our custom shoulder and posture support — shoulder, posture or both in one, 3–8 mm for the styles this thickness choice applies to. For lower-back support rather than shoulder support, our neoprene back braces cover a different part of the body.

 

SBR or CR neoprene — which is right for a shoulder and posture support?

SBR is the standard choice for most shoulder and posture supports, and CR is the choice where the support will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a support worn at a desk, at work or in the gym. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a support used outdoors, on site or in the sun.

The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the shoulder without a fight; SBR is firmer and holds the support's shape through a working day. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor use and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for sweat and wiping clean after wearBetter for repeated wet use and outdoor work
Best forDesk, work and gym supportsOutdoor and premium supports

A support range often sells alongside other braces: our neoprene knee braces use the same laminated foam and the same sizing logic, so a brand can order the two together in one size range.

 

Who is a neoprene shoulder and posture support for — and who is it not for?

Sports shops — supports for players returning to training after a shoulder strain, with your logo and your size range.

Health product brands — a posture support sold as part of your own health range, made to your design and your packaging.

Office-wellness sellers — supports for desk workers with rounded backs and sore shoulders, slim enough to wear under a work shirt.

Workwear and safety suppliers — supports for people who lift and carry at work, where a little extra support through the day makes the shift easier.

When neoprene is NOT the right choice

  • If the wearer is recovering from surgery or a serious shoulder injury — a clinician should be asked first, and a medical brace may be needed.
  • If the wearer needs a rigid brace that stops the shoulder moving — neoprene gives gentle support, not rigid fixing.
  • If the wearer needs heavy-lifting support — a firm lifting belt or back brace fits that job better.
  • If the lowest possible unit cost is the whole brief — a thin elastic posture strap fits a one-season budget better than a neoprene support.

 

Customisation Options

Tell us which of these your support needs, and we will build the sample to your drawing.

  • Logo: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Sizes: graded to your own size range.
  • Strap layout: shoulder straps, back panel and fastening placed to your drawing.
  • Fabric face: smooth nylon jersey or another fabric face to your design.
  • Packaging: polybag as standard; hangtag, retail box and instruction card on request.

 

Frequently Asked Questions

Can it be worn under a shirt?
Yes. The support is slim and stretchy, so it fits under everyday clothing without a hard outline, and the wearer can put it on and take it off without help.

Is this for the shoulder, for posture, or for both?
It can be either, or both in one design. Tell us which your customers need — a shoulder panel, a posture back panel, or the two together — and we lay out the straps to your drawing.

What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size range and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the strap layout and the size range. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We make shoulder and posture supports to your drawing, your strap layout and your size range, and we check the fit and the strap placement on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom shoulder and posture support and we will confirm the best material and thickness for your wearers.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. Shoulder support, posture support, or both in one
  3. The size range, with chest measurements
  4. Thickness or material preference — SBR, SCR or CR
  5. Logo and colours
  6. Packaging — polybag, hangtag, retail box or instruction card

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A support is worn for hours, so strap placement and fit decide whether it gets worn at all. Send us the size range and we will make you a sample to try on.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.