NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Polyester Fabric
  • Neoprene Polyester Fabric
  • Neoprene Polyester Fabric
Neoprene Polyester FabricNeoprene Polyester FabricNeoprene Polyester Fabric

Neoprene Polyester Fabric

Neoprene polyester fabric is laminated neoprene (SBR, SCR or CR foam + a polyester face), usually 3 mm thick, that gives bags, covers and daily goods a hard-wearing, low-cost outside that sews cleanly and stands up to daily use. Bag makers, cover makers and home brands order it for the outer face of everyday products, because polyester is tough, cheap and easy to print. It is sold as flat sheets for makers to cut, not as a finished cover or bag. Send us your design drawing, the products the fabric is cut for and the thickness, and we will confirm the best foam grade and thickness for bags, covers and daily goods.

We make polyester fabric in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and laminate the polyester face under one roof, so a change to the thickness or the face can be checked on a sample before bulk production starts.

A polyester face has to sew cleanly, so the lamination matters more than the colour. We laminate the polyester face to the foam under heat and pressure, so the face does not peel at the cut edge, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The polyester face takes print well, so a bag maker's logo stays bright after months of daily use.

The fabric is commonly supplied as flat sheets, because a flat sheet cuts cleanly on a maker's table and wastes less than a roll that curls at the edges. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished fabric by cutting a bag panel from it and stitching it, because a face that frays at the seam is a face that ends up in the offcut bin.

 

What thickness of neoprene is best for polyester fabric?

3 mm is the standard for most polyester fabric. It gives a good balance of strength, a low cost and a face that still sews cleanly. For the full range, see our neoprene sheet thickness guide.

2 mmLight bags, covers and daily goods where weight mattersLeast padding; not enough for a product that must also cushion
3 mmMost polyester fabric; bags, covers and daily goodsBest balance of strength, a low cost and an easy sew
5 mmHeavy covers, work bags and daily goods that take a beatingMost padding, but heavier and stiffer to cut and sew

Measure the product, not the fabric name. Measure the largest panel the fabric must cover and the thickness the finished product needs, and tell us whether the product is sewn or glued: fabric ordered by name alone often fits the panel and leaves no room for the seam, or covers the seam and pulls short at the edge. See our custom polyester fabric — made to your thickness and size for the styles this thickness choice applies to. For a neoprene camouflage fabric face rather than a polyester fabric face, see our neoprene camouflage fabric.

 

SBR or CR neoprene — which is right for polyester fabric?

SBR is the standard foam under a polyester face, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a bag, cover or daily product used on land or indoors. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a bag or cover sold for the beach and daily salt-water use.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the product without a fight; SBR is firmer and holds a bag's shape when it is hung up to dry.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday bags, covers and daily goodsBeach, sea and premium bags and covers

If the face needs a printed artwork rather than a plain hard-wearing surface, the product changes: our neoprene printed fabric carry a brand's artwork across the whole surface, and a polyester face and a printed face are ordered from different sheets.

 

Who is neoprene polyester fabric for — and who is it not for?

Bag makers — polyester-faced sheets in your colours, cut to your panel sizes, for bags that take daily use.

Cover makers — a tough face for covers and daily goods, made to your thickness, for products that must last.

Home brands — fabric printed with your logo for the goods you sell, made to fit your range exactly.

Promo suppliers — polyester-faced sheets that take print well, so your client's logo stays bright after months of use.

When neoprene is NOT the right choice

  • If the finished product needs a soft hand feel — a jersey face suits a soft brief better than a polyester face.
  • If the face must stretch a long way — a lycra or spandex face stretches further than a polyester face.
  • If the fabric is only for a lining — a thinner, lighter face fits a lining brief better than a 3 mm laminated sheet.
  • If the lowest possible unit cost is the whole brief — an unlaminated foam sheet fits a one-season budget better than a polyester-faced sheet.

 

Customisation Options

Tell us which of these your polyester fabric needs.

  • Print: sublimation for full-colour artwork, screen print for spot logos, on the polyester face.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: 2 mm, 3 mm or 5 mm, split to your order.
  • Foam grade: SBR, SCR or CR foam under the face, to your design.
  • Sheet size: cut to your panel size, or supplied as full sheets.
  • Packaging: flat sheets as standard; rolls on request.

 

Frequently Asked Questions

Will the polyester face peel at the cut edge?
No, not if the lamination is right. We laminate the polyester face to the foam under heat and pressure, so the face does not peel at the cut edge — tell us the product and we check the lamination on the sample.

Can the face be printed with our logo?
Yes. The polyester face takes print well, so your logo stays bright after months of daily use — send the artwork with your drawing and we confirm the print before sampling.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We supply polyester fabric to your thickness, your print and your size, and we check the the face on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom polyester fabric and we will confirm the best foam grade and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The finished products the fabric is cut for
  3. The thickness you need
  4. Foam grade — SBR, SCR or CR
  5. Print and colours
  6. Packaging — flat sheets or rolls

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A polyester face is judged on the cutting table, not on a roll. Send us the product size and we will make you a sample sheet to cut.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.