NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Perforated Foam Sheets
  • Neoprene Perforated Foam Sheets
  • Neoprene Perforated Foam Sheets
Neoprene Perforated Foam SheetsNeoprene Perforated Foam SheetsNeoprene Perforated Foam Sheets

Neoprene Perforated Foam Sheets

Neoprene perforated foam sheets are laminated neoprene sheets (SBR, SCR or CR foam + fabric) punched with small holes, usually 3 mm thick, that let air and sweat pass through, for breathable supports that must not trap heat against the skin. Support makers, brace makers and sports brands order them for the body of supports worn all day, because the holes keep the skin dry where a solid sheet would sweat. They are not plain foam sheets, so the holes are part of the sheet and cannot be added later. Send us your design drawing, the products the sheets are cut for and the thickness, and we will confirm the best foam grade and thickness for breathable supports.

We make perforated foam sheets in our own factory in China, where we have made neoprene products for 15 years. We foam the rubber, split the sheet to thickness and finish the surface under one roof, so a change to the thickness or the finish can be checked on a sample before bulk production starts.

A perforated sheet has to breathe evenly, so the hole pattern matters more than the thickness. We punch the holes after lamination, so the holes stay round and even across the sheet, and the foam is split to the thickness you ask for, so every sheet in the order cuts the same. The holes are spaced to let air through without weakening the sheet, so a support holds its shape all day.

The sheets are commonly supplied flat, because a flat sheet cuts cleanly on a maker's table and keeps the hole pattern lined up across panels. The foam grade can be SBR for everyday lines, SCR for more stretch or CR for seawater use, and the whole sheet wipes clean after cutting. We check the finished sheets by cutting a support panel from them and wearing it, because a sheet that does not breathe is a sheet that ends up in the offcut bin.

 

What thickness of neoprene is best for perforated foam sheets?

3 mm is the standard for most perforated foam sheets. It gives a good balance of airflow, cushioning and a sheet that still cuts cleanly. For the full range, see our neoprene sheet thickness guide.

2 mmLight breathable supports and linings where airflow matters mostLeast cushioning; not enough for a support that must also pad
3 mmMost perforated foam sheets; breathable supportsBest balance of airflow, cushioning and a clean cut
5 mmHeavy supports, work padding and gear that must also protectMost padding, but heavier and slower to dry

Measure the product, not the sheet name. Measure the largest panel the sheet must cover and the airflow the finished product needs, and tell us whether the product is sewn or glued: sheets ordered by name alone often fit the panel and leave no room for the seam, or cover the seam and pull short at the edge. See our custom perforated foam sheets — made to your thickness and size for the styles this thickness choice applies to. For a neoprene adhesive-backed foam sheets face rather than a perforated foam sheets face, see our neoprene adhesive-backed foam sheets.

 

SBR or CR neoprene — which is right for perforated foam sheets?

SBR is the standard foam for perforated sheets, and CR is the choice where the finished product will live in seawater. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a breathable support or pad used on land or indoors. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a breathable support sold for the beach, the sea and hot weather.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it moves with the body without a fight; SBR is firmer and holds a support's shape when it is hung up to dry.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday breathable supportsBeach, sea and premium breathable supports

If the sheet must stick to a surface rather than breathe, the product changes: our neoprene adhesive-backed foam sheets stick to a surface for padding that must stay put, and a perforated sheet and an adhesive-backed sheet are ordered from different sheets.

 

Who is neoprene perforated foam sheets for — and who is it not for?

Support makers — perforated sheets in your colours, cut to your panel sizes, for supports that must breathe all day.

Brace makers — a breathable sheet for braces worn close to the skin, made to your thickness, for products where airflow is the point.

Sports brands — fabric in your colours for the supports you sell, made to fit your range exactly.

Medical suppliers — perforated sheets for supports worn all day, so the skin stays dry under the brace.

When neoprene is NOT the right choice

  • If the finished product must keep water out — a solid sheet resists splashes better than a perforated sheet.
  • If the holes must be very large — large holes weaken the sheet, and a mesh face suits an open brief better than perforation.
  • If the sheet is only for a lining — a thinner, lighter sheet fits a lining brief better than a 3 mm perforated sheet.
  • If the lowest possible unit cost is the whole brief — an unperforated foam sheet fits a one-season budget better than a perforated sheet.

 

Customisation Options

Tell us which of these your perforated foam sheets needs.

  • Hole pattern: hole size and spacing to your drawing, punched evenly across the sheet.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Thickness: 2 mm, 3 mm or 5 mm, split to your order.
  • Foam grade: SBR, SCR or CR foam, to your design.
  • Sheet size: cut to your panel size, or supplied as full sheets.
  • Packaging: flat sheets as standard; rolls on request.

 

Frequently Asked Questions

Will the holes weaken the sheet?
No, not if the pattern is right. The holes are spaced to let air through without weakening the sheet, so a support holds its shape all day — tell us the product and we check the pattern on the sample.

Can the holes be made bigger or smaller?
Yes. Hole size and spacing are punched to your drawing — tell us the airflow you need and we confirm the pattern before sampling.

What is the minimum order?
20 sheets per order as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and the thickness you need and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the thickness and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We supply perforated foam sheets to your thickness, your print and your size, and we check the the airflow on a sample on a sample before bulk production. The general minimum order is 20 sheets per order as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom perforated foam sheets and we will confirm the best foam grade and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The finished products the sheets are cut for
  3. The hole size and spacing you need
  4. Foam grade — SBR, SCR or CR
  5. Print and colours
  6. Packaging — flat sheets or rolls

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A perforated sheet is judged on the skin, not on a roll. Send us the product size and we will make you a sample sheet to cut.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.