NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Diving Equipment

  • Neoprene Diving Wetsuits
  • Neoprene Diving Wetsuits
  • Neoprene Diving Wetsuits
Neoprene Diving WetsuitsNeoprene Diving WetsuitsNeoprene Diving Wetsuits

Neoprene Diving Wetsuits

A neoprene diving wetsuit is a close-fitting suit made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 5 mm thick, that keeps a diver warm underwater. Dive brands, schools and rental fleets order it for scuba diving. It is not a drysuit, so it does not keep the diver dry. Send us your design drawing, water temperature and sizes, and we will confirm the best material and thickness for scuba diving.

We manufacture custom neoprene diving wetsuits in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished suit under one roof, so a change to a panel or a seam can be checked on a sample before bulk production starts.

A scuba suit is glued and blind-stitched: the glue holds the panels together first, and the blind stitch passes only part-way through the foam, so the needle does not punch a line of holes straight through to the water. Sealed seams can be added on request, with tape or a liquid seal over the stitching, where a diver will spend a long time in cold water. A plain overlock stitch is cheaper, but it leaves a line of needle holes, and on a scuba suit that is the first place cold water flushes in.

We cut body panels to a tolerance of about 2 mm, because a chest panel cut short pulls the back zip off-centre and gaps at the neck, and a neck that gaps lets in cold water on every descent. The neck, wrists and ankles are cut to sit close without cutting in, and the zip is usually placed at the back or the chest to your drawing, so the suit is easy to get into on a rocking boat and stays shut underwater.

Knees and shoulders rub against tanks, boat decks and dive gear, so those panels can be reinforced with a harder-wearing face where you ask for it. Inside, a nylon jersey lining slides on over skin or a rash guard and dries between dives, and sizes are graded to your size chart, so a school fleet looks like one fleet and a brand range looks like one brand.

 

What thickness of neoprene is best for scuba diving?

5 mm is the standard for most recreational scuba diving. It is warm enough for most dive sites and still flexible enough to swim, climb a boat ladder and handle gear, which is why most of the scuba suits we make are cut in 5 mm. For the full range, see our neoprene sheet thickness guide.

ThicknessBest forTrade-off
3 mmWarm water and short dives; easy to move in and easy to packLeast insulation; not enough for cold water or long bottom times
5 mmMost recreational scuba diving; the standard choiceBest balance of warmth, flexibility and bulk
7 mmCold water, winter diving and long divesWarmest, but heavier and stiffer to swim and climb in

Measure the diver, not the size label. Take chest, waist, hips, height and arm length, and send all five with your enquiry: a suit ordered by height alone often fits the torso and gaps at the neck, or fits the chest and pulls short at the wrist. See our custom diving wetsuits — full suits and shorties, 3–8 mm, glued and blind-stitched for the styles this thickness choice applies to. Divers who also wear boots with open-heel fins can look at our neoprene dive boots as a matching item.

 

SBR or CR neoprene — which is right for scuba diving?

CR is the usual choice for scuba diving, and SBR is the usual choice where cost matters more than salt-water life. CR (chloroprene rubber) resists UV, ozone and seawater better, so a suit that will be used in sun and salt air, dive after dive, holds up longer in CR. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for warm-water school fleets and rental suits that are replaced often.

The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, which is what a diver feels when pulling a suit on; SBR is firmer and lighter. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and shorter outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional water contact and warm-water divingBetter for repeated diving and seawater use
Best forWarm-water school and rental fleetsScuba suits used often in cold water, sun and salt air

For surface water sports rather than scuba, the choice changes: our neoprene surf and SUP suits use thinner foam and a different seam plan, because a surfer is in and out of the water and needs flexibility more than deep-water insulation.

 

Who is a neoprene diving wetsuit for — and who is it not for?

Dive brands — your own cut, your own colours and your own logo on a scuba suit your customers trust below the surface, made to your tech pack and size chart.

Dive schools and dive centres — matching sets for students and instructors, with size marking that survives repeated washing and suits that survive daily teaching use.

Rental fleets — reinforced knees and shoulders, sealed seams and numbered sizes for easy hire, built to be worn by many different divers, dive after dive.

Distributors and e-commerce sellers — mixed sizes in one order, retail-ready packaging with hangtag on request, for shops that sell scuba suits to divers who already own the rest of their kit.

When neoprene is NOT the right choice

  • If the diver must stay dry, not just warm — a drysuit, not a wetsuit, is the right product.
  • If the suit is only for snorkelling or surface swimming — a thinner shorty or surf suit fits better and costs less to make.
  • If the diver needs maximum flexibility for freediving — a suit built for scuba, with sealed seams and 5–7 mm foam, will feel stiff and restrictive.
  • If the lowest possible unit cost is the whole brief — a thinner SBR suit for warm water, or a different product entirely, fits the budget better.

 

Customisation Options

Tell us which of these your suit needs, and we will build the sample to your drawing.

  • Logo: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Sizes: graded to your own size chart, from junior to adult sizes.
  • Seams and zips: sealed seams on request; back zip or chest zip to your design.
  • Reinforcement: knee and shoulder panels where your divers need extra wear resistance.
  • Packaging: polybag as standard; hangtag and retail packaging on request.

 

Frequently Asked Questions

Are these wetsuits made for scuba diving?
Yes. This page is for scuba diving wetsuits, with sealed seams available and foam commonly in 5–7 mm, for dives below the surface — not for surface swimming.

What do sealed seams do on a scuba suit?
Sealed seams close the stitching so cold water does not flush through the suit during a dive. They are available on request for scuba suits, where staying warm underwater matters most.

What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and sizes and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the diving conditions and the sizes you need. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We make scuba suits to your drawing, your size chart and your diving conditions, and we check the fit and the seams on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom diving wetsuits and we will confirm the best material and thickness for your divers.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The diving conditions — water temperature and dive depth
  3. The sizes you need, with your size chart
  4. Thickness or material preference — SBR, SCR or CR
  5. Logo and colours
  6. Packaging — polybag, hangtag or retail packaging

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A good scuba suit is decided before it is cut: the water, the sizes and the seams. Send us those three things and we will make you a sample to try in the water.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.