NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Bags

  • Neoprene Bottle & Tumbler Holders
  • Neoprene Bottle & Tumbler Holders
  • Neoprene Bottle & Tumbler Holders
Neoprene Bottle & Tumbler HoldersNeoprene Bottle & Tumbler HoldersNeoprene Bottle & Tumbler Holders

Neoprene Bottle & Tumbler Holders

A neoprene bottle holder is a snug sleeve of laminated neoprene (SBR, SCR or CR foam + fabric), usually 3–5 mm thick, that wraps one bottle or tumbler to insulate the drink and cushion it against knocks. Drink brands and sports shops order it for one bottle in a bag, at the gym or car. It holds one bottle only. Send us your design drawing and bottle size, and we will confirm the best material and thickness.

We manufacture custom neoprene bottle and tumbler holders in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished holder under one roof, so a change to the fit or the print can be checked on a sample before bulk production starts.

The fit is the whole product: a holder cut too tight is a struggle to slide on, and a holder cut too loose lets the bottle slip out when the bag tips over. We cut the sleeve to the bottle diameter with about 2 mm of grip allowance, so it holds without stretching the seam, and we stitch the base flat or shaped to the bottom of the bottle, so the bottle sits level on a desk instead of wobbling.

The top edge is commonly finished with a bound or folded hem, so it does not fray after repeated use, and a handle, a shoulder strap or a small pocket can be added where you ask for it. Any handle is stitched and reinforced at the fixing points, because a handle that pulls away from a full bottle is the first thing a customer notices — so we bar-tack the fixing and check it by pulling the finished holder by its handle before packing.

The fabric face is what the customer touches and sees, so it is chosen with the print in mind: a smooth face takes a printed logo cleanly, while a textured face suits a plainer, everyday holder. The foam inside insulates the drink and cushions the bottle against knocks in a bag, and the whole holder wipes clean after a spill.

 

What thickness of neoprene is best for a bottle holder?

5 mm is the standard for most bottle and tumbler holders. It gives a good balance of insulation, cushioning and a neat fit around the bottle, which is why most of the holders we make are cut in 5 mm. For the full range, see our neoprene sheet thickness guide.

ThicknessBest forTrade-off
3 mmSlim holders that slide into a bag or a car cup holder; short carriesLeast insulation and cushioning; not enough for all-day carrying
5 mmMost bottle and tumbler holders; daily useBest balance of insulation, cushioning and slim fit
7 mmBottles carried all day or knocked around in a gym bagMost insulation and cushioning, but heavier and bulkier

Measure the bottle, not the volume. Two bottles of the same volume can have different diameters, so measure the diameter at the widest point and the full height, and tell us whether the bottle tapers towards the top. See our custom bottle and tumbler holders — made to your bottle diameter and height, 3–8 mm for the styles this thickness choice applies to. For a smaller cup rather than a bottle, our neoprene coffee cup sleeves are the closer page.

 

SBR or CR neoprene — which is right for a bottle holder?

SBR is the standard choice for most bottle holders, and CR is the choice where the holder will live outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a holder carried to the gym, the office or school. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a holder sold with outdoor gear, used at the beach or left in the sun.

The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it grips a tapered tumbler without a fight; SBR is firmer and holds a neat cylindrical shape. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor use and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and condensationBetter for repeated wet use and seaside use
Best forGym, office and school bottle holdersOutdoor, beach and premium bottle holders

If the drink is a slim can rather than a bottle, the shape changes again: our neoprene slim can coolers are cut to a can diameter, not a bottle diameter, and the two should not be ordered from the same pattern.

 

Who is a neoprene bottle holder for — and who is it not for?

Drink brands and tumbler sellers — a holder printed with your logo that travels with the bottle or tumbler you sell, made to fit your bottle exactly.

Gift companies — a branded holder as a corporate gift or a promotional item, in your colours, for conferences, events and welcome packs.

Sports shops and gym suppliers — holders for gym bags and training kits, where a bottle is carried every day and knocked around between sessions.

Schools and office suppliers — holders for school bags and desks, sized to the bottles children and office workers actually carry.

When neoprene is NOT the right choice

  • If you need to carry several bottles together — a multi-bottle carrier with dividers, not a single-bottle sleeve, is the right product.
  • If the bottle needs hard drop protection — neoprene cushions knocks, but a hard case protects against a hard fall onto concrete.
  • If the drink must stay cold for many hours without an ice pack — a holder slows warming, but it is not a cooler box.
  • If the lowest possible unit cost is the whole brief — a thin fabric sleeve, or a printed label on the bottle itself, fits the budget better.

 

Customisation Options

Tell us which of these your holder needs, and we will build the sample to your drawing.

  • Logo: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Size: made to your bottle or tumbler diameter and height.
  • Carrying: handle, shoulder strap or pocket where you ask for one.
  • Fabric face: smooth nylon jersey or another fabric face to your design.
  • Packaging: polybag as standard; hangtag and retail packaging on request.

 

Frequently Asked Questions

Will it fit my tumbler?
Yes, if you send the diameter and height. We make the holder to your bottle or tumbler size, so it grips without being hard to slide on — measure the diameter at the widest point, not the volume on the label.

Can I add a handle or a strap?
Yes. A handle, a shoulder strap or a small pocket can be added where you ask for it, stitched and reinforced at the fixing points so it takes the weight of a full bottle.

What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and bottle size and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the bottle or tumbler size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We make bottle and tumbler holders to your bottle size, your print and your carrying choice, and we check the grip on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom bottle and tumbler holders and we will confirm the best material and thickness for your bottle.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The bottle or tumbler diameter and height
  3. The quantity you need
  4. Thickness or material preference — SBR, SCR or CR
  5. Logo and colours
  6. Packaging — polybag, hangtag or retail packaging

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A holder that fits is a holder that gets used every day. Send us the bottle measurements and we will make you a sample to try on the real bottle.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.