NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene Applications

  • Neoprene Coasters
  • Neoprene Coasters
  • Neoprene Coasters
Neoprene CoastersNeoprene CoastersNeoprene Coasters

Neoprene Coasters

A neoprene coaster is a small flat mat of laminated neoprene (SBR, SCR or CR foam + fabric), usually 3 mm thick, that sits under a cup or glass to soak up condensation and protect the table from heat and rings. Cafés, bars, drink brands and gift companies order it for coffee, tea and cold drinks at the table. It sits under one cup only, not under a plate. Send us your design drawing and coaster size, and we will confirm the best material and thickness.

We manufacture custom neoprene coasters in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished coasters under one roof, so a change to the size or the print can be checked on a sample before bulk production starts.

A coaster has one job and it is judged in seconds: a wet glass put down on a bare table leaves a ring, and a hot mug leaves a mark, so the coaster has to take the moisture and the heat before the table does. We cut the foam so the top face absorbs the condensation from a cold glass instead of letting it run off the edge, and the base grips the table so the coaster stays where it is put when the cup is lifted and set down again.

The edge is where a cheap coaster gives itself away. A raw cut edge frays and curls after a few washes, and a curled edge lets a cup rock, so we finish the edge with a bound hem or a clean sealed cut to your drawing, and we check the finished coaster by laying it flat on a table and pressing each corner to make sure nothing lifts. A coaster that lies flat is a coaster a café will keep using.

The top face is the brand surface, so it is chosen with the print in mind: a smooth face takes a printed logo, a menu illustration or a full-colour photograph cleanly, while a textured face suits a plainer coaster for everyday use. The foam inside cushions the cup when it is set down hard, and the whole coaster rinses clean under a tap and dries flat, ready for the next service.

 

What thickness of neoprene is best for coasters?

3 mm is the standard for most neoprene coasters. It is thick enough to absorb condensation and cushion a cup, and thin enough to stack neatly and slip into a gift set, which is why most of the coasters we make are cut in 3 mm. For the full range, see our neoprene sheet thickness guide.

ThicknessBest forTrade-off
3 mmMost coasters for cups, mugs and glasses; cafés, bars and gift setsBest balance of absorption, grip and a slim stack
5 mmHeavy mugs and thick glassware; coasters that take hard daily useMore cushioning and heat protection, but a taller stack
7 mmBar coasters under large glasses and jugs; extra protection for soft wood tablesMost cushioning, but bulky for a table setting

Measure the cup, not the saucer. Take the diameter of the base of the cup or glass that will sit on the coaster, and add a few millimetres of margin so the cup does not overhang the edge, then tell us whether the coaster should be round or square. See our custom neoprene coasters — round or square, 3–8 mm for the styles this thickness choice applies to. For a large mat that covers the table under a plate rather than a single cup, our neoprene placemats are the closer page.

 

SBR or CR neoprene — which is right for coasters?

SBR is the standard choice for most coasters, and CR is the choice where the coaster will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a coaster used in a café, a bar or an office. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a coaster sold with outdoor drinkware or used at a beach bar.

The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps a curved glass base without a fight; SBR is firmer and holds a neat round or square shape through repeated washing. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor use and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forCafé, bar and office coastersOutdoor, beach and premium coasters

For a sleeve that wraps the cup itself instead of sitting under it, our neoprene coffee cup sleeves are the closer page.

 

Who is a neoprene coaster for — and who is it not for?

Cafés and coffee shops — a coaster printed with your logo that sits under every cup you serve, made to your cup size, so your brand is on the table for the whole visit.

Drink brands and breweries — a branded coaster as a bar item or a gift with a bottle, in your colours, for pubs, events and promotional packs.

Gift companies — a coaster set as a corporate gift or a souvenir, with a printed photograph or message, for conferences, hotels and welcome packs.

Bars and restaurants — coasters that protect wood tables from rings and heat, sized to your glassware, and rinsed clean between services.

When neoprene is NOT the right choice

  • If you need to protect a whole table under plates — a placemat, not a coaster, covers the place setting.
  • If the cup needs hard drop protection — neoprene cushions a cup set down hard, but a hard tray protects against a fall to the floor.
  • If the drink must stay hot for a long time — a coaster slows cooling, but it is not a heated mat.
  • If the lowest possible unit cost is the whole brief — a thin paper coaster fits a one-use budget better than a reusable neoprene coaster.

 

Customisation Options

Tell us which of these your coasters need, and we will build the sample to your drawing.

  • Logo: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Size: made to your cup or glass diameter, round or square to your drawing.
  • Shape: round or square as standard; a custom outline to your drawing on request. Thickness: 3 mm as standard; 5 mm or 7 mm where you need more cushioning.
  • Fabric face: smooth nylon jersey or another fabric face to your design.
  • Packaging: polybag as standard; hangtag and retail packaging on request.

 

Frequently Asked Questions

Will the coaster soak up condensation from a cold glass?
Yes. The foam face takes up the condensation from a cold glass so it does not run onto the table, and the coaster rinses clean under a tap and dries flat afterwards.

Can I print a photograph on a coaster?
Yes. A smooth fabric face takes a full-colour printed photograph, a logo or an illustration cleanly by sublimation, so send us the artwork with your design drawing.

What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and the coaster size and shape and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the coaster size and shape and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We make custom neoprene coasters to your coaster size, your print and your shape, and we check the grip and the flat lay on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom neoprene coasters and we will confirm the best material and thickness for your coasters.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The coaster size and shape — round or square
  3. The quantity you need
  4. Thickness or material preference — SBR, SCR or CR
  5. Logo and colours
  6. Packaging — polybag, hangtag or retail packaging

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A coaster is judged by whether it lies flat and keeps the table dry. Send us the cup size and we will make you a sample to try under a real glass.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.