A neoprene card holder is a slim sleeve made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 3 mm thick, that holds a few cards in slim slots for light daily carry. Fashion shops, gift shops and accessory brands order it for cards and light daily carry, because it is thinner and smaller than a wallet and slips into a front pocket. It holds cards only, with no cash pocket. Send us your design drawing, the holder size and the slot count, and we will confirm the best material and thickness for cards and light daily carry.
We manufacture custom neoprene card holders in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished card holder under one roof, so a change to the holder size or the slots can be checked on a sample before bulk production starts.
A card holder is judged by the grip, so the slots matter more than the print. We cut the holder to your size with slim card slots stitched through the foam, so the cards sit flat and do not slip out, and the edges are finished with a bound hem so they do not fray after months of daily use. The whole holder wipes clean after a day in a pocket, and the foam does not stretch out the way a thin fabric holder does.
3 mm is the standard for most card holders. It gives a good balance of a slim shape, a firm grip and a holder that still fits in a pocket, which is why most of the card holders we make are cut in 3 mm. For the full range, see our neoprene sheet thickness guide.
| 3 mm | Most card holders; a few cards and light daily carry | Best balance of a slim shape and a firm grip in a pocket |
|---|---|---|
| 5 mm | Thicker card holders for more cards and for a padded feel | More padding, but bulkier in a front pocket |
| 7 mm | Premium card holders and holders for a structured look | Most structure, but stiff to slide cards in and out |
Measure the cards, not the holder. Tell us the number of cards and the card size, and we cut the holder to that load: a holder ordered by length alone often comes out too narrow for the cards, or too loose to grip them. Send the card count with your enquiry, so the slots are laid out to fit them all. See our custom card holders — made to your design, 3–8 mm, with your logo and colours for the styles this thickness choice applies to. For a wallet for cash and cards rather than a slim holder for cards only, our neoprene wallets are the closer page.
SBR is the standard choice for most card holders, and CR is the choice where the holder will be used outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a holder carried in a pocket or a bag. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a holder sold with beach gear or left in the sun.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the holder panels without a fight; SBR is firmer and holds the holder flat and neat in a pocket. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday card holders for pockets and bags | Beach, outdoor and premium card holders |
If the holder must carry coins as well as cards, the shape changes: Our neoprene coin purses are cut from the same laminated neoprene, and the two are ordered from different patterns.
Fashion shops — a card holder printed with your label that customers carry every day, made to your colours and your size.
Gift shops — card holders for birthday gifts and holiday sets, in colours that match the season.
Accessory brands — a holder in your colours for your own line, made to your exact slot layout.
Corporate gift buyers — a branded card holder as a staff gift or a client gift, in your colours, that is used every day.
When neoprene is NOT the right choice
Tell us which of these your card holder needs, and we will build the sample to your drawing.
How many cards will the holder grip?
Tell us the number before we cut. The slots are laid out to your drawing, so a holder for three cards is cut differently from a holder for six — send the card count and we will lay out the slots to fit them.
Will the cards slip out of the holder?
No, not if the slots are cut right. The slots grip each card flat, so the cards stay put in a pocket — tell us the card size and we will cut the slots to it.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the holder size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom card holders to your drawing, your size and your print, and we check the slots and the grip on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom card holders and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A card holder is judged every time a card slides in and out. Send us the card count and we will make you a sample to try with real cards.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.