A neoprene bottle carrier is a padded bag made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 5 mm thick, that carries several bottles or cans, with dividers between them. Drink brands, breweries and event organisers order it for picnics, parties and shop shelves. It is not a single-bottle sleeve. Send us your design drawing, bottle count and bottle size, and we will confirm the best material and thickness for your carrier.
We manufacture custom neoprene bottle and can carriers in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished carrier under one roof, so a change to the bottle count or the handle can be checked on a sample before bulk production starts.
A carrier that holds several bottles has to take real weight, so the way it is built matters. The walls are cut from laminated neoprene and stitched with dividers between the bottles, so glass does not clink and cans do not dent on the way there, and the base is cut to sit flat under a full load instead of sagging in the middle.
The handle is the part that fails first on a cheap carrier, so we stitch it through the body panel and bar-tack the fixing points, and we check the finished carrier by lifting it by the handle with the full bottle count inside. A shoulder strap can be added where you ask for it, for a carrier that is walked a long way to a picnic or a market stall.
We cut the divider spacing to the bottle diameter with a few millimetres of clearance: too tight and a bottle jams on the way in, too loose and the bottles knock together. The outside is the brand surface, so the fabric face takes a printed logo, a product name or a short message cleanly, and the whole carrier wipes clean after a spill.
5 mm is the standard for most bottle and can carriers. It gives a good balance of cushioning, insulation and a carrier that holds its shape under a full load, which is why most of the carriers we make are cut in 5 mm. For the full range, see our neoprene sheet thickness guide.
| Thickness | Best for | Trade-off |
|---|---|---|
| 3 mm | Light carriers for a short carry to a picnic or a party; easy to fold and store | Least cushioning; sags more under a full load of glass |
| 5 mm | Most two, four and six-bottle carriers; daily shop and picnic use | Best balance of cushioning, insulation and shape under load |
| 7 mm | Glass bottles carried over rough ground or stacked in a shop | Most cushioning and insulation, but heavier and bulkier |
Measure the bottles, not the word on the label. A "wine bottle" can be tall and slim or short and wide, so measure the diameter at the widest point and the full height of the actual bottle or can, and tell us the count. See our custom bottle and can carriers — two, four, six or another count, 3–8 mm for the styles this thickness choice applies to. For a carrier that is a gift set rather than a picnic carrier, our neoprene wine and bottle carriers page covers multi-bottle gift carrying.
SBR is the standard choice for most bottle carriers, and CR is the choice where the carrier will live outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a carrier used at picnics, parties and market stalls. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a carrier sold with outdoor gear or used at the beach.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps a mixed load of bottles and cans without a fight; SBR is firmer and holds the carrier's shape when it is empty on a shelf. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and condensation | Better for repeated wet use and seaside use |
| Best for | Picnic, party and shop carriers | Outdoor, beach and premium carriers |
If you only need one bottle at a time, the carrier is the wrong shape: our neoprene bottle and tumbler holders are snug sleeves for a single bottle, with no dividers and no carry handle to pay for.
Drink brands and breweries — a four- or six-bottle set for your shop, printed with your label, that carries your drinks home as one pack.
Gift shops — carriers that turn several bottles or cans into one ready gift, in your colours, for holidays, housewarmings and corporate gifts.
Event organisers — carriers for canned drinks at outdoor gatherings, where a hard crate is heavy to move and glass needs cushioning.
Retailers and market sellers — a carrier that works as shelf packaging and as a bag the customer keeps, so your brand travels home with the drinks.
When neoprene is NOT the right choice
Tell us which of these your carrier needs, and we will build the sample to your drawing.
How many bottles does one carrier hold?
As many as you design it for — two, four, six or another count. Tell us the bottle count and size in your drawing and we lay out the dividers to fit.
Will the glass bottles clink together?
No, not if the dividers are cut to the bottle size. Foam dividers sit between the bottles so glass does not clink or chip, and the base stays flat under a full load.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and bottle count and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the bottle count, the bottle size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make bottle and can carriers to your bottle count, your bottle size and your print, and we check the handle and the dividers on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom bottle and can carriers and we will confirm the best material and thickness for your carrier.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A carrier is judged by its handle and its dividers. Send us the bottle count and size and we will make you a sample to load and carry.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.