NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene For Bracer

  • Neoprene Shin Guards
  • Neoprene Shin Guards
  • Neoprene Shin Guards
Neoprene Shin GuardsNeoprene Shin GuardsNeoprene Shin Guards

Neoprene Shin Guards

A neoprene shin guard is a pad of laminated neoprene (SBR / SCR / CR foam + fabric), usually 5 mm thick, worn over the shin to take the knocks of tackles, kicks and blocks in football and martial arts. It is not a knee sleeve: it protects the shin below the knee, not the joint. Send us your design drawing, the sport and the guard length, and we will confirm the best material and thickness.

We manufacture custom shin guards in our own factory in China, where we have made neoprene products for 15 years. Every guard starts as a sheet of laminated neoprene foam, cut to the curve of the shin, then bound, fitted with straps or a sleeve, and printed to your design. Because the foam, the fabric face and the finished guard are all made under one roof, we can change the shape, the length or the fixing on a sample and see the result the same week.

The guard must hold its curve against the leg, and that is where the making shows. We cut the pad to the shape of the shin and bind the edges all round, so the pad keeps its curve instead of flattening out after a few matches. The straps sit above and below the calf muscle, not over it, because a strap over the muscle works loose every time the player runs. A sleeve-fit version must be cut to the same rule: snug at the calf and the ankle, with room for the muscle in between.

The failure we watch for is a guard that curls at the corners, because a curled edge catches on a sock and lifts the whole pad during a match. It happens when the binding is pulled too tight around a thick pad, so we bind thick guards with a wider binding and check the corners flat before packing. Football and combat sports want different guards: football guards are light and slim under a sock, while combat guards are wider and thicker for kicks and blocks.

 

What thickness of neoprene is best for a shin guard?

5 mm is the standard for a shin guard. It cushions tackles and kicks well while still letting the player run freely. A thinner guard is lighter under a sock but takes less impact; a thicker guard protects more but feels heavier on the leg over a full match. For the full range of choices, see our neoprene sheet thickness guide.

ThicknessBest forTrade-off
3 mmYouth football, light training, slim guards under a sockLeast cushioning; not enough for hard tackles
5 mmAdult football and general contact sport — the standard guardBest balance of impact protection, flexibility and weight
7 mmMartial arts sparring and hard tackles, where impact is heaviestHeavier on the leg; too bulky under a tight sock

Measure the shin, not the player's height. Measure from just below the knee to just above the ankle, along the front of the leg, and measure the calf at its widest point too — a guard cut from height alone is too long for some players and too short for others. Send the shin length and the age group with your drawing, and tell us whether the guard will be worn under a sock or over it. See our custom neoprene shin guards — slim football or wide combat shape, 3–8 mm for the guard this page is about.

 

SBR or CR neoprene — which is right for a shin guard?

SBR is the usual choice for a shin guard. It is the lower-cost foam, it cushions impact well, and it is light enough to run in for a full match. Most guards we make are SBR, because a guard is worn for a few hours at a time and does not need the toughest foam we make. CR is the tougher foam: it resists UV and ozone better and keeps its spring for longer, so choose CR for a premium guard, or for guards that will be used outdoors in strong sun season after season.

SBRCR
CostLower cost; the usual choice for team guardsCosts more; chosen for premium or outdoor guards
UV and ozone resistanceGood enough for regular outdoor playBetter; holds up in strong sun over many seasons
Water useFine for sweat and rain on the pitchBetter for wet and outdoor conditions
Best forStandard football and training guardsPremium guards and heavy outdoor use

On our own technical data sheet, CR foam measures 3–5° hardness, 276.32 kg/m³ density on a 51″×130″ sheet, 860 kPa tensile strength and 550% elongation, while SBR foam at 10–15° hardness measures 158.34 kg/m³, 256 kPa and 185% elongation. Those are foam-sheet figures, and the higher CR tensile strength is what lets a CR guard take repeated hard knocks without tearing at the edge. SCR sits between the two on cost and on resistance to sun and ozone, and it is worth asking about if your guard must be tougher than SBR without moving to CR.

 

Who is a neoprene shin guard for — and who is it not for?

Football clubs — a set of shin guards for a youth or adult team, in your team colours, sized by shin length so every player on the pitch is covered.

Martial arts schools — wider, thicker guards stocked for sparring sessions, where students need protection that stays soft and flexible instead of a hard shell.

Sports shops — shin guards for players who take knocks to the shins, sold with boots, socks and other match gear, in youth and adult sizes.

Sports brands — your logo on a guard sold as part of your own football or martial arts range, made to your design and your size chart. Players who only need gentle support around the calf, with no impact to take, should look at our neoprene calf sleeves instead — a sleeve supports the muscle, it does not shield the bone.

When neoprene is NOT the right choice

  • Players who need a rigid, hard-shell guard for the highest level of impact should choose a hard plastic guard — neoprene cushions, it does not act as a shell.
  • A shin guard is not a knee or ankle support, and it does not protect the joint itself.
  • Buyers who need the lowest possible unit cost for a one-off giveaway should choose a thin plastic guard instead — neoprene costs more to make.

 

Customisation Options

Tell us the sport, the shape and the fixing, and we will cut the guard to your drawing. These are the choices most buyers change.

  • Logo: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Length: guard length to your drawing.
  • Sizes: graded to your own size range.
  • Holding: straps or sleeve fit, so the guard stays over the shin through a match.
  • Packaging: polybag as standard; hangtag and retail packaging on request.

 

Frequently Asked Questions

Do I wear shin guards under or over my socks?
Under the socks is the usual way for football. The sock holds the guard against the shin and stops it shifting during a match. A strap-fit guard can be worn either way, but the sock-over method is the one most teams use — tell us which way your players wear them, because it changes how snug the guard should be.

Do kids need a different guard from adults?
Yes. A youth guard is shorter, narrower and usually thinner — 3 mm is the common choice for youth football, while adults usually take 5 mm. Do not order one size for a whole school: send the shin lengths by age group and we will grade the sizes from them, so the smallest players are not wearing guards that reach their knees.

What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order. Mixed sizes can share one design, so a club can cover youth and adult teams in one order.

Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing, the sport and the guard length and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the sport, the guard length and the sizes. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

If your players take knocks to the shins every match, a guard that stays in place and keeps its curve is the difference between protection they trust and protection they keep adjusting. The general minimum order is 200 pieces per design, adjustable to your actual order; we support sampling, usually in 5–7 days, and bulk production usually takes 15–18 days after sample approval. Request a quote for custom neoprene shin guards and send your drawing with it — we will confirm the best material and thickness for your players before we cut the sample.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. Sport (football, martial arts or other)
  3. Guard length and shin measurements
  4. Thickness or material preference (SBR, SCR or CR)
  5. Logo and colours
  6. Packaging

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

Send the drawing, and we will come back with a guard that stays over the shin for the whole match.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.