A neoprene paddle board cover is a wide padded sleeve made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 5 mm thick, that wraps a whole paddle board to protect it against scratches, dings and sun. Paddle board brands and water sports shops order it for storing a board at home and carrying it to the water. It is not a surfboard cover, because a paddle board is wider and flatter. Send us your design drawing, the board length and width, and we will confirm the best material and thickness for storage and transport.
We manufacture custom neoprene paddle board covers in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished cover under one roof, so a change to the width or the nose shape can be checked on a sample before bulk production starts.
A paddle board cover has to follow a wide, flat outline, so the width matters as much as the length. We cut the cover to the board outline with a shaped nose pocket and a tail that closes flat, so the board slides in without catching, and the seams are placed at the rails where they do not press on the deck. The opening is commonly a zip along the side or a drawstring at the tail, and the zip is placed so its teeth never touch the board surface when the cover is opened and closed.
The nose is reinforced where the board is carried nose-first through doorways and car parks, and a carry handle or a shoulder strap can be added where you ask for it, so the board is carried to the water by hand. The fabric face wipes clean after a sandy session, and the foam inside cushions the board against knocks in a van or on a roof rack. We check the finished cover by sliding the real board in and out, because a cover that fights the board is a cover that stays in the garage.
5 mm is the standard for most paddle board covers. It gives a good balance of ding protection, sun protection and a cover that still folds for storage, which is why most of the covers we make are cut in 5 mm. For the full range, see our neoprene sheet thickness guide.
| 3 mm | Light covers for a short carry to the water and for boards stored indoors | Least ding protection; not enough for a board thrown in a van |
|---|---|---|
| 5 mm | Most paddle board covers; storage and transport | Best balance of protection, sun cover and a foldable fit |
| 7 mm | Boards flown as luggage or carried on roof racks | Most protection, but heavier and harder to fold |
Measure the board, not the word on the label. An all-round board can be many widths, so measure the full length, the widest width and the thickness, and tell us the nose and tail shape. See our custom paddle board covers — made to your board length and width, 3–8 mm, with zip or drawstring for the styles this thickness choice applies to. For a dry bag that travels on the board rather than a cover for the board, our neoprene dry bags are the closer page.
SBR is the standard choice for most paddle board covers, and CR is the choice where the cover will live outdoors. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a cover used to carry a board to the water and store it indoors. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a cover left on a roof rack, stored in the sun or used at the beach every day.
The numbers from our own technical data sheet show why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it wraps the wide rails without a fight; SBR is firmer and holds the cover flat and neat on the board. SCR sits between the two on cost and stretch, and we use it where a customer wants more give than SBR without paying for CR.
| SBR | CR | |
|---|---|---|
| Cost | Lower cost; the usual choice for everyday lines | Costs more than SBR |
| UV and ozone resistance | Fair; best for indoor storage and short outdoor use | Better; holds up longer in sun, ozone and salt air |
| Water use | Fine for occasional splashes and wiping clean | Better for repeated wet use and seaside use |
| Best for | Everyday paddle board covers for water and storage | Roof-rack, beach and premium paddle board covers |
If the board is a surfboard rather than a paddle board, the shape changes: our neoprene surfboard covers are cut narrower for a surfboard outline, and the two should not be ordered from the same pattern.
Paddle board brands — a cover printed with your logo that travels with the board you sell, made to fit your board shapes exactly.
Water sports shops — covers in the lengths and widths your customers actually paddle, with size marking that survives the shop floor.
Rental fleets — matching covers for a fleet of hire boards, so the boards survive daily hire and the fleet name is seen at the launch point.
Online paddle stores — a cover that ships flat, fits a wide range of board sizes and photographs well, for customers who buy board protection online.
When neoprene is NOT the right choice
Tell us which of these your cover needs, and we will build the sample to your drawing.
Will the cover fit an inflatable paddle board?
Yes, if you send the size. Tell us the inflated length, width and thickness and we cut the cover to the inflated board — a cover cut for a hard board will not fit an inflatable of the same length.
Can I carry the board by the cover handle?
Yes, where you ask for one. A carry handle or a shoulder strap can be added, stitched and reinforced at the fixing points so it takes the weight of the board on the walk to the water.
What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.
Can I get a sample first?
Yes — we support sampling, usually in 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.
How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.
How do I order?
Send us your design drawing, the size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.
We make custom paddle board covers to your drawing, your size and your print, and we check the fit on a sample before bulk production. The general minimum order is 200 pieces per design, adjustable to your actual order; sampling is supported, usually in 5–7 days; and bulk production usually takes 15–18 days after sample approval. Request a quote for custom paddle board covers and we will confirm the best material and thickness for your order.
Request a Quotation
To help us review your inquiry, please send:
Website: https://www.neoprenecustom.com/ Email: kevin@neoprenecustom.com
A board cover is judged by the board sliding in cleanly. Send us the board outline and we will make you a sample to try on the real board.
Contact: Kevin
Phone: 13417385320
Tel: 0734-87965514
Email: kevin@neoprenecustom.com
Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.