NEOPRENE FACTORY: TIANCHI TECHNOLOGY CO., LTD.

Neoprene For Bracer

  • Neoprene Finger Sleeves
  • Neoprene Finger Sleeves
  • Neoprene Finger Sleeves
Neoprene Finger SleevesNeoprene Finger SleevesNeoprene Finger Sleeves

Neoprene Finger Sleeves

A neoprene finger sleeve is a small tube made from laminated neoprene (SBR, SCR or CR foam + fabric), usually 3 mm thick, that slides over one finger to protect it against knocks, friction and cold. Sports shops and team suppliers order it for volleyball players, basketball players and climbers whose fingers take repeated impact. It covers one finger only, so it does not support the whole hand. Send us your design drawing, the finger sizes and the sleeve length, and we will confirm the best material and thickness for finger protection and sports.

We manufacture custom finger sleeves in our own factory in China, where we have made neoprene products for 15 years. We cut the foam, laminate the fabric face and stitch the finished finger sleeve under one roof, so a change can be checked on a sample before bulk production starts.

A finger sleeve has to stay on a moving finger, so the taper matters more than the length. We cut the sleeve to the finger measurement with a slight taper toward the tip, so it grips without cutting off circulation, and the top edge is finished with a bound hem so it does not roll down during a game. The inside face is smooth, so the sleeve slides on over a taped finger without catching on the tape.

The sleeve is commonly stitched with a flat seam along the side, placed where it does not rub between two fingers, and the bottom edge is left open so the finger can bend freely at the knuckle. A grip print can be added on the palm side where you ask for it, so the ball does not slip on a wet day, and the whole sleeve wipes clean after training. We check the finished sleeve by bending a finger in it many times, because a sleeve that creeps up the finger is a sleeve that ends up in the kit bag.

 

What thickness of neoprene is best for a finger sleeve?

3 mm is the standard for most finger sleeves. It gives a good balance of protection, grip and a sleeve that still bends with the finger. For the full range, see our neoprene sheet thickness guide.

2 mmLight sleeves for taping over and for players who want the thinnest feelLeast padding; not enough for a hard knock on the fingertip
3 mmMost finger sleeves; volleyball, basketball and climbingBest balance of protection, grip and a free bend
5 mmGoalkeepers, climbers and fingers that have been hurt beforeMost padding, but stiffer and harder to bend for a full game

Measure the finger, not the glove size. Measure around the finger at the knuckle and at the middle joint, and the length from the knuckle to the fingertip, and send all three with your enquiry: a sleeve ordered by glove size alone often fits the length and grips too tight at the joint. See our custom finger sleeves — made to your design, 3–8 mm for the styles this thickness choice applies to. For a thumb brace rather than a finger sleeve, see our neoprene thumb braces.

 

SBR or CR neoprene — which is right for finger sleeves?

SBR is the standard choice for most finger sleeves, and CR is the choice where the sleeve will be used outdoors in sun and sea air. SBR (styrene-butadiene rubber) is the lower-cost foam and is fine for a sleeve worn indoors for volleyball, basketball or climbing. CR (chloroprene rubber) resists UV, ozone and seawater better, so choose CR for a sleeve sold for beach volleyball, sailing or outdoor training in the sun.

Our technical data sheet shows why the two foams feel different: our CR foam measures 3–5° Shore C hardness, 276.32 kg/m³ density, 860 kPa tensile strength and 550% elongation, while our SBR (10–15°) measures 10–15° hardness, 158.34 kg/m³ density, 256 kPa tensile strength and 185% elongation. CR is softer and stretches further, so it bends with the finger without a fight; SBR is firmer and holds the sleeve round and neat between games.

SBRCR
CostLower cost; the usual choice for everyday linesCosts more than SBR
UV and ozone resistanceFair; best for indoor storage and short outdoor useBetter; holds up longer in sun, ozone and salt air
Water useFine for occasional splashes and wiping cleanBetter for repeated wet use and seaside use
Best forEveryday finger sleeves for indoor sportsOutdoor, beach and premium finger sleeves

If the whole hand needs protection rather than one finger, the product changes: our neoprene-wrist-braces-supplier are built around the palm and the wrist for grip on the bar, and a finger sleeve and a glove are ordered from different patterns.

 

Who is a neoprene finger sleeve for — and who is it not for?

Sports shops — sleeves in your colours for volleyball, basketball and climbing players, made to your finger size range, for customers who want one finger protected without a full glove.

Team suppliers — matching sleeves for a whole squad, with size marking that survives the kit bag, for teams that order the same sleeve season after season.

Online sports stores — a sleeve that photographs well, ships flat and fits a wide size range, for customers who buy finger protection online.

Climbing gyms — sleeves in your colours for the climbers in your gym, so sore fingers keep climbing and your gym name is seen on every wall.

When neoprene is NOT the right choice

  • If the whole hand must be protected — a glove, not a single-finger sleeve, is the right product.
  • If the finger needs medical support after an injury — this is a protective sleeve, not a medical splint, and a clinician should be asked first.
  • If the sleeve must be very thick and stiff — a rigid finger splint suits fixed support better than a soft neoprene tube.
  • If the lowest possible unit cost is the whole brief — a thin fabric finger band fits a one-season budget better than a neoprene sleeve.

 

Customisation Options

Tell us which of these your finger sleeve needs.

  • Logo: sublimation for full-colour artwork, screen print for spot logos, rubber patch or woven label for a premium finish.
  • Colour: black as standard; custom colours and Pantone matching on request.
  • Size: made to your finger circumference at the knuckle and the middle joint, and to your sleeve length.
  • Grip print: a grip pattern on the palm side where you ask for it, for ball sports and climbing.
  • Fabric face: smooth nylon jersey or another fabric face to your design.
  • Packaging: polybag as standard; hangtag and retail packaging on request.

 

Frequently Asked Questions

Will the sleeve stay on during a game?
Yes, if it is cut to the finger. We taper the sleeve toward the tip and finish the top edge with a bound hem so it does not roll down — send the knuckle and middle-joint measurements and we cut to them, not to a glove size.

Can I wear it over a taped finger?
Yes. The inside face is smooth so the sleeve slides on over tape without catching, and the open bottom edge lets the finger bend at the knuckle — tell us the tape thickness and we allow for it in the cut.

What is the minimum order?
200 pieces per design as a general minimum, adjustable to your actual order.

Can I get a sample first?
Yes — sampling usually takes 5–7 days. Send us your design drawing and size and we will confirm the sample cost and time.

How long does bulk production take?
Usually 15–18 days after sample approval, depending on the quantity and customisation.

How do I order?
Send us your design drawing, the size and the quantity. We confirm the material, thickness and price, then make a sample for your approval before bulk production.

We make custom finger sleeves to your drawing, your size and your print, and we check the the fit on a sample on a sample before bulk production. The general minimum order is 200 pieces per design as a general minimum, adjustable to your actual order; sampling usually takes 5–7 days; bulk production usually takes 15–18 days after sample approval. Request a quote for custom finger sleeves and we will confirm the best material and thickness for your order.

 

Request a Quotation

To help us review your inquiry, please send:

  1. Your design drawing / artwork
  2. The finger sizes you need, at the knuckle and the middle joint
  3. The sleeve length — fingertip to knuckle, or longer
  4. Thickness or material preference — SBR, SCR or CR
  5. Logo and colours
  6. Packaging — polybag, hangtag or retail packaging

Website: https://www.neoprenecustom.com/   Email: kevin@neoprenecustom.com

A finger sleeve is judged in the middle of a game, not on a hanger. Send us the finger sizes and we will make you a sample to try on a real finger.

CONTACT US

Contact: Kevin

Phone: 13417385320

Tel: 0734-87965514

Email: kevin@neoprenecustom.com

Add: Intersection of Zhangjialing Road and Science and Technology Road, Guiyang Industrial Park, Guiyang Town, Qidong County, Hengyang City, Hunan Province./Dongguan Factory(GUANXIN): Shixin Street, Fushan Village, Liaobu Town, Dongguan, Guangdong Province.